MPLAB ICD 2 In-Circuit Debugger (DV164005)

Please consider the MPLAB ICD 3 (DV164035). The MPLAB ICD 2 is not recommended for new designs and will not support new MCU or dsPIC devices released after September 2010.

This item is not available for the academic discount.

Click here to go to the MPLAB ICD 3 page.

An all-in-one debugger/programmer solution: MPLAB® ICD 2 is a low cost, real-time debugger and programmer for selected PIC® MCUs and dsPIC® DSCs. Using Microchip Technology's proprietary In-Circuit Debug functions, programs can be downloaded, executed in real time and examined in detail with the debug functions of MPLAB. Set watch variables and breakpoints from symbolic labels in C or assembly source code, and single step through C source lines or into assembly code. MPLAB ICD 2 can also be used as a development programmer for supported MCUs.


The secret behind In Circuit Debugging is two dedicated hardware lines (microcontroller pins used only during debugging mode) that control In Circuit Serial Programming™ (ICSP™) of the device and, afterwards, debugging through proprietary, on-chip firmware. The ICD 2 debug features are built into the microcontroller and activated by programming the debug code into the target processor. There is some shared overhead expense that includes one stack level, some general purpose file registers and a small area of program memory when in the debug mode.
IMPORTANT NOTE: MPLAB ICD 2 requires minimal design guidelines be followed to ensure stable communications between the unit and the target.

The MPLAB ICD 2 connects using USB or RS-232 between the design engineer's PC operating with MPLAB IDE and their product board (target) being developed. It acts as an intelligent interface/translator between the two, allowing the engineer to look into the active target board's microcontroller, viewing variables and registers at breakpoints with MPLAB watch windows. A breakpoint can be set to halt the program at a specific location. The program can be single-stepped or run at full speed. At breakpoints, data and program memory can be read and modified. Additionally, the MPLAB ICD 2 can be used to program or reprogram the Flash-based microcontroller while installed on the board.

Возможности

    • USB (Full Speed 2 M bits/s) & RS-232 interface to host PC
    • Real time background debugging
    • MPLAB IDE GUI (free copy included)
    • Built in over-voltage/short circuit monitor
    • Firmware upgradeable from PC
    • Totally enclosed
    • Supports low voltage to 2.0 volts. (2.0 to 6.0 range)
    • Diagnostic LEDs (Power, Busy, Error)
    • Reading/Writing memory space and EEDATA areas of target microcontroller
    • Programs configuration bits
    • Erase of program memory space with verification
    • Peripheral freeze-on-halt stops timers at breakpoints
MPLAB ICD 2 In-Circuit Debugger DV164005

Используемые компоненты

Производитель: Microchip Technology Inc.
Наименование
Производитель
Описание Корпус/
Изображение
Цена, руб. Наличие
DV164005
DV164005
Microchip Technology Inc.
Арт.: 50975 ИНФО PDF RD OBS
Поиск
предложений
Внутрисхемный отладчик MPLAB ICD2 c поддержкой микроконтроллеров PIC18C601 & 801, PIC18F/248, 258, 442, 448, 452, 458, 6620, 6720, 8620 & 8720, USB кабель. RS-232, USB, ISP/ICP
DV164005
-
Поиск
предложений
DV164035
DV164035
Microchip Technology Inc.
Арт.: 316746 ИНФО PDF RD
Доступно: 2895 шт. от: 15090 руб.
MPLAB ICD 3 (DV164035) - внутрисхемный отладчик/программатор подходит для работы с микроконтроллерами и цифровыми сигнальными контроллерами (DSC) компании Microchip. Работает MPLAB ICD 3 под управлением бесплатной универсальной среды разработчика MPLAB IDE с интуитивно понятным интерфейсом.. RS-232, USB, ISP/ICP
DV164035 15090,00
7 шт.
(на складе)
2888 шт.
(под заказ)