Wave Shield for Arduino Kit - v1.1 (ADAFRUIT INDUSTRIES)

Wave Shield for Arduino Kit - v1.1, ADAFRUIT INDUSTRIES Wave Shield for Arduino Kit - v1.1, ADAFRUIT INDUSTRIES Wave Shield for Arduino Kit - v1.1, ADAFRUIT INDUSTRIES
Наименование Wave Shield for Arduino Kit - v1.1
Производитель ADAFRUIT INDUSTRIES(ADAFRUIT)
Артикул 1228576

Adafruit Wave Shield for Arduino Kit - v1.1 Добавить качественный звук к электронному проекту удивительно трудно. Перед вами музыкальный модуль для Arduino, который решает эту проблему. Шилд поддерживает диапазон частот до 22 кГц и 12 бит объём несжатого аудио файла. Он имеет встроенный ЦАП, фильтр и операционный усилитель для высококачественного вывода. Звуковые файлы считываются из памяти SD / MMC карт. Модуль поставляется набором, который необходимо собрать самому. Контроллер Arduino, SD-карта, инструменты, динамик и наушники в набор не включены. Этот шилд несовместим с контроллерами Mega и Леонардо. Adding quality audio to an electronic project is surprisingly difficult. Here is a shield for Arduinos that solves this problem. It can play up to 22KHz, 12bit uncompressed audio files of any length. It's low cost, available as an easy-to-make kit. It has an onboard DAC, filter and op-amp for high quality output. Audio files are read off of an SD/MMC card, which are available at nearly any store. Volume can be controlled with the onboard thumbwheel potentiometer. This shield is a kit, and comes with all parts you need to build it. Arduino, SD card, tools, speaker and headphones are not included. It is fairly easy to construct and anyone with a successful soldering project under their belt should be able to build it. The shield comes with an Arduino library for easy use; simply drag uncompressed wave files onto the SD card and plug it in. Then use the library to play audio when buttons are pressed, or when a sensor goes off, or when serial data is received, etc. Audio is played asynchronously as an interrupt, so the Arduino can perform tasks while the audio is playing. Can play any uncompressed 22KHz, 16bit, mono Wave (.wav) files of any size. While it isnt CD quality, it is certainly good enough to play music, have spoken word, or audio effects. Check out the demo video/audio at the webpage Output is mono, into L and R channels, standard 3.5mm headphone jack and a connection for a speaker that is switched on when the headphones are unplugged Files are read off of a FAT16/FAT32-formatted SD/MMC card Included library and examples makes playing audio easy Please note that the library is rather bulky, requiring 10K of flash and more than 1/2 K of RAM for buffering audio. It works fine using an yATmega328-based Arduino (Duemilanove, Uno or compatible). This shield is not Mega or Leonardo compatible!

Производитель: ADAFRUIT
adafruit-wave-shield-audio-shield-for-arduino.pdf
VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record - v2 (ADAFRUIT)
от 1660,00 Склад (1-2 дн)

VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record - v2 This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip.…

FRDM-KL05Z Evaluation Board (EMBEST)

Бюджетная макетная плата на базе ARM Cortex-M0+ микроконтроллера MKL05Z32VFM4 семейства Kinetis L.USB, OPEN SDA, ARDUINO

FRDM-KL25Z Eval board (EMBEST)

Макетная плата на базе новейшего Cortex-M0+ микроконтроллера Kinetis KL25Z128VLK4 от Freescale.SWD, USB Arduino

Cyclone V GX Starter Kit (TERASIC)
от 18310,00 Склад (1-2 дн)

Отладочный набор на базе ПЛИС 5CGXFC5C6F27C7N семейства Cyclone V GX.USB-UART, USB-JTAG, HDMI, HSMC, microSD, ArdH, A