16-Channel 12-bit PWM/Servo Shield - I2C interface (ADAFRUIT INDUSTRIES)

16-Channel 12-bit PWM/Servo Shield - I2C interface, ADAFRUIT INDUSTRIES 16-Channel 12-bit PWM/Servo Shield - I2C interface, ADAFRUIT INDUSTRIES 16-Channel 12-bit PWM/Servo Shield - I2C interface, ADAFRUIT INDUSTRIES
Наименование 16-Channel 12-bit PWM/Servo Shield - I2C interface
Производитель ADAFRUIT INDUSTRIES(ADAFRUIT)
Артикул 1227561

Adafruit 16-Channel 12-bit PWM/Servo Shield - I2C interface You want to make a cool Arduino robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that the Arduino has only a few PWM outputs, and maybe those outputs are conflicting with another shield! What now? You could give up OR you could just get our handy PWM and Servo driver shield. It's just like our popular PWM/Servo Breakout but now Arduino-ready and works with any Arduino that uses shields: Uno, Leo, Mega, ADK, its all good. When we saw this chip, we quickly realized what an excellent add-on this would be. Using only two I2C pins, control 16 free-running PWM outputs! You can even stack up 62 shields to control up to 992 PWM outputs (which we would really like to see since it would be glorious and like 4 feet tall) Because I2C is a shared bus you can also connect other I2C devices and sensors to the SCL/SDA pins as long as their addresses don't conflict (this shield has address 0x40) There's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V Arduino and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can stack up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output We wrapped up this lovely chip into a shield with a couple nice extras Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green and red power-good LEDs 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header Stackable design. You'll need to pick up stacking headers and right angle 3x4 headers in order to stack on top of this shield without the servo connections getting in the way. A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins A lot of extra space remaining? Let's turn it into a prototyping area. You get a 5x20 proto area for any extra wiring you'd like to add This product comes with a fully tested and assembled shield as well as 4 pieces of 3x4 male straight header (for servo/LED plugs), a 2-pin terminal block (for power) and a stick of 0.1" header so you can plug into an Arduino. A little light soldering will be required to assemble and customize the board by attaching the desired headers but it is a 15 minute task that even a beginner can do. If you want to use right-angle 3x4 headers, we also carry a 4 pack in the shop. Servos and Arduino not included - but we do sell tons of different servos in the shop so pick up a few while you're here! Dimensions (no headers or terminal block) 2.1" x 2.7" x 0.1" (54mm x 70mm x 3mm)

16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit (ADAFRUIT)
от 1240,00 Склад (1-2 дн)

Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit Raspberry Pi - отличный одноплатный компьютер, но он не очень подходит для управления…

Uno R3 (HKSHAN)
от 545,00 Склад (1-2 дн)

Arduino Uno - R3 - Версия R3 отличается от предыдущих версий конвертером USB-UART на базе ATmega16U2 вместо ранее используемых чипов 8U2 и FTDI

DFRduino UNO R3 (DFROBOT)
от 1150,00 Склад (1-2 дн)

DFRduino UNO R3 100 % копия оригинальной Arduino UNO R3. Arduino UNO построена на микроконтроллере ATmega328 и конвертере USB-UART на базе ATmega8U2. Плата имеет 14 цифровых каналов ввода/вывода (6 из которых может использоваться в качестве выводов ШИМ), 6 аналоговых каналов вывода, 4 UART, кварцевый генератор на 16 МГц, разъем USB, гнездо питания, колодка ICSP и кнопка сброса.…

Uno R3 [Atmega 328P-AU+CH340G] (HKSHAN)
от 363,00 Склад (1-2 дн)

Arduino Uno R3 [Atmega 328P-AU+CH340G] по своим характеристикам не чем не отличается от оригинала Arduino UNO R3

Nano V3.0 (HKSHAN)
от 575,00 Склад (1-2 дн)

Arduino Nano V3.0 (не оригинал) - это маленькое, готовое к использованию и хорошо работающее с макетными платами устройство, разработанное на микроконтроллере ATmega328.…

Mega 2560 R3 (HKSHAN)
от 938,00 Склад (1-2 дн)

Arduino Mega 2560 (не оригинал) Это плата управления с микроконтроллером ATmega2560. На этой плате есть 54 канала дискретного ввода/вывода (14 каналов можно использовать в режиме ШИМ), 16 аналоговых входов, 4 последовательных порта, резонатор на 16 МГц, разьём USB и кнопка Reset.…

Motor party add-on pack for Arduino (ADAFRUIT)
от 2850,00 Склад (1-2 дн)

Motor party add-on pack for Arduino Make your own Arduino motor party with a motor shield and a fine assortment of motors! New! we've upgraded the shield to our new version 2, with more powerful drivers, and uses fewer pins to boot! Included in this add-on pack is: Motor shield V2 for Arduino 6 volt DC hobby motor Small stepper motor Standard size servo Micro size servo An Arduino is not included, and you'll need one to use the shield.…

HS-5645MG Digital High Torque Metal Gear. Dual BB (HITEC)
от 2570,00 Склад (1-2 дн)

HS-5645MG Digital High Torque Metal Gear. Dual BB Hitec HS-5645MG - цифровое серво. Комбинация силы, скорости и цены, а так же большой силы на удержании, делают серво фаворитом среди вертолётчиков и пилотов самолётов.…

Thermocouple Amplifier MAX31855 breakout board - v2.0 (ADAFRUIT)
от 1090,00 Склад (1-2 дн)

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The MAX31855K does everything for you, and can be easily interfaced with any microcontroller, even one without an analog input.…

HS-82MG Standard Metal Gear Micro (HITEC)
от 1380,00 Склад (1-2 дн)

HS-82MG Standard Metal Gear Micro Hitec HS82MG с металлическим передаточным механизмом - одно из новейших серво Hitec, близкое к HS-81MG. Микросерво HS-82 MG обладает прекрасным балансом скорости и вращающего момента.…

HS-45HB AGTT Feather. Karbonite. Top BB (HITEC)
от 1040,00 Склад (1-2 дн)

HS-45HB AGTT Feather. Karbonite. Top BB Серво Hitec HS-45HB свойственны экономичность и надёжность всех других серво Hitec, притом её вал поддерживается шарикоподшипником, а шестерни сделаны из карбонита.…

Mini Maestro18 USB Servo Controller (POLOLU)
от 2240,00 Склад (1-2 дн)

18-ти канальный контроллер сервоприводов может управляться командами через порт USB, внутренними скриптами или через последовательный порт.Контроллер может управлять каждым сервоприводом независимо от всех остальных сервоприводов.

В НАЛИЧИИ 4шт.
1200,00
Расчет доставки...