RoboClaw 2x15A Motor Controller with USB, ORION ROBOTICS

RoboClaw 2x15A Motor Controller with USB Двухканальный контроллер DС коллекторных моторов 2x15 Amp Description The RoboClaw 2x15 Amp motor controller is an extremely efficient, versatile, dual channel synchronous regenerative motor controller. It can supply two brushed DC motors with 15 Amps continuous and 30 Amps peak. The RoboClaw also includes a 3 Amp switch mode BEC. Power any device from RoboClaw safely with plenty of power to spare. RoboClaw supports multiple sensor inputs including dual quadrature encoders with up to 19.6 million pulses per second, potentiometers and absolute encoders.With dual quadrature decoding you get greater control over speed, velocity and direction. Automatically maintain speed and direction even if the load changes. With the ability to use potentiometers you can easily create giant servo systems and control them from any of RoboClaw's interface modes. The RoboClaw motor controller comes equipped with several built in modes to controller your motors. Use standard RC receiver/transmitter, serial devices, analog sources or a microcontroller such as an Arduino. As a synchronous regenerative motor controller RoboClaw will charge the attached battery during a slow down or breaking action. With the advance circuitry it can also change direction during full throttle without damage! RoboClaw also incorporates a lithium cutoff mode which protects your batteries from damage. Get the power to win your next robotics competition! Downloads - Data Sheet - Python Example for Raspberry Pi, OSX, Linux, Windows - Roboclaw Windows Setup Application - Roboclaw C# Class Library Source Code - USB Roboclaw WIndows Driver - Arduino Library and Examples Features - USB Interface - 3.3V Compliant Outputs - 5V Tolerant Inputs - Quadrature Encoders - Absolute Encoders - Position and Velocity Control - Encoders Supported in all Modes - High Resolution Current Sense - High Speed Direction Change - 5V 3 Amp Switch Mode BEC - Battery Level Monitoring - Dual Channel Quadrature Decoding - Dual 19,600,000 PPS Per Channel - Thermal Protection - Regenerative Breaking - Serial, RC or Analog Control - Easy to Use - Can be Bussed

RoboClaw 2x15A Motor Controller with USB, ORION ROBOTICS

Параметры RoboClaw 2x15A Motor Controller with USB

НаименованиеRoboClaw 2x15A Motor Controller with USB

Документация для RoboClaw 2x15A Motor Controller with USB

Сопутствующие товары для RoboClaw 2x15A Motor Controller with USB

  • Изображение  The DaVinci Arduino Compatible

    The DaVinci Arduino Compatible

    Склад (1-2 дн)

    The DaVinci is an Arduino compatible board with several unique features to facilitate its use in robotics. The DaVinci includes a 2 pin screw terminal for use with batteries as the primary power source. It also includes a jumper to set RTS or DTR as the reset signal. In addition it includes a low profile USB connector. This prevent the USB connector from interfering with over sized shields. The DaVinci also includes dual mount pattern which makes it functional with existing projects and compatible with mounting in robotics. Downloads The DaVinci The new DaVinci is a 100% Arduino compatible board. It was designed to support standard shields and work in robotics systems. The main features are the improved regulators, low profi le capacitors, low profile USB connector and screw terminals for power. The low profile parts prevent interference with all shields. The additional mount pattern fits a standard mount for currently available robots. The DaVinci ships with a pre-programmed socketed Atmel. The reset control can be set by jumper to DTR or RTS control. Standard TX , RX and ON leds are on board. Improved regulators were used to decrease drop out voltages. The TX / RX from the Arduino can be removed from circuit to isolated the Arduinos only UART. Documentation Arduino is a 100% open source solution. Hardware and software. In keeping with that tradition we have included the schematics to this board at the end of the data sheet. All programming documentation is supplied by the Arduino community. The Arduino IDE and programming guides can be downloaded from http:///www.arduino.cc

Изображения RoboClaw 2x15A Motor Controller with USB

RoboClaw 2x15A Motor Controller with USB, ORION ROBOTICS RoboClaw 2x15A Motor Controller with USB, ORION ROBOTICS
Цена (включая НДС)
5770,50 руб
Наличие на складах
Нет на складе,
сообщить о поступлении
Уведомить о поступлении

Заметили ошибку в работе сайта?
Скажите нам об этом