Терраэлектроника

MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier], Pololu Robotics and Electronics

MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier] The Pololu MinIMU-9 v3 is a compact (0.8 ? 0.5) board that combines ST's L3GD20H 3-axis gyroscope and LSM303D 3-axis accelerometer and 3-axis magnetometer to form an inertial measurement unit (IMU); we therefore recommend careful reading of the L3GD20H datasheet (3MB pdf) and LSM303D datasheet (1MB pdf) before using this product. These sensors are great ICs, but their small packages make them difficult for the typical student or hobbyist to use. They also operate at voltages below 3.6 V, which can make interfacing difficult for microcontrollers operating at 5 V. The MinIMU-9 v3 addresses these issues by incorporating additional electronics, including a voltage regulator and a level-shifting circuit, while keeping the overall size as compact as possible. The board ships fully populated with its SMD components, including the L3GD20H and LSM303D, as shown in the product picture. Compared to the previous MinIMU-9 v2, the v3 version offers a number of improvements arising from the use of newer MEMS sensors, including a wider maximum magnetic sensing range and better gyroscopic accuracy and stability. This version also adds a pin for changing the sensor slave addresses, allowing two MinIMUs to be on the same I?C bus. The MinIMU-9 v3 is pin-compatible with the MinIMU-9 v2, but changes in I?C addresses and configuration registers might require some changes to software written for older versions (this should not be an issue if you are using our Arduino libraries). The MinIMU-9 v3 is pin-compatible with the AltIMU-10 v4, which offers the same functionality augmented by a digital barometer that can be used to obtain pressure and altitude measurements. The AltIMU includes a second mounting hole and is 0.2 longer than the MinIMU. Any code written for the MinIMU-9 v3 should also work with the AltIMU-10 v4. The L3GD20H and LSM303D have many configurable options, including dynamically selectable sensitivities for the gyro, accelerometer, and magnetometer. Each sensor also has a choice of output data rates. The two ICs can be accessed through a shared I?C/TWI interface, allowing the sensors to be addressed individually via a single clock line and a single data line. Additionally, the SA0 pin is accessible, allowing users to change the slave addresses and have two MinIMUs connected on the same I?C bus (For additional information, see the I?C Communication section below). The nine independent rotation, acceleration, and magnetic readings (sometimes called 9DOF) provide all the data needed to make an attitude and heading reference system (AHRS). With an appropriate algorithm, a microcontroller or computer can use the data to calculate the orientation of the MinIMU board. The gyro can be used to very accurately track rotation on a short timescale, while the accelerometer and compass can help compensate for gyro drift over time by providing an absolute frame of reference. The respective axes of the two chips are aligned on the board to facilitate these sensor fusion calculations. (For an example of such a system using an Arduino, see the picture below and the Sample Code section at the bottom of this page.) The carrier board includes a low-dropout linear voltage regulator that provides the 3.3 V required by the L3GD20H and LSM303D, allowing the module to be powered from a single 2.5 V to 5.5 V supply. The regulator output is available on the VDD pin and can supply almost 150 mA to external devices. The breakout board also includes a circuit that shifts the I?C clock and data lines to the same logic voltage level as the supplied VIN, making it simple to interface the board with 5 V systems. The board's 0.1 pin spacing makes it easy to use with standard solderless breadboards and 0.1 perfboards. Характеристики: - Рабочее напряжение: от 2,5 до 5,5 В - Потребляемый ток: 6 мА - Выходной формат (I?C): - Гироскоп: 16-бит на ось (чтение). - Акселерометр: 16-бит на ось (чтение, выравнивание по левому краю). - Магнитометр: 16-бит на ось (чтение, выравнивание по правому краю). - Диапазон чувствительности (конфигурируемый): - Гироскоп: ±245, ±500 или ±2000 °/сек - Акселерометр: ±2, ±4, ±6, ±8 или ±16 g - Магнитометр: ±2, ±4, ±8 или ±12 Гс - Размеры (без штырьевых разъёмов): 20 х 13 х 3 мм - Вес (без штырьевых разъёмов): 0,7 гр


MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier], Pololu Robotics and Electronics

Параметры MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier]

НаименованиеMinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier]
ПроизводительPololu Robotics and Electronics (POLOLU)
Артикул1923249

Аналоги MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier], доступные на складе

Изображения MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier]

MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier], Pololu Robotics and Electronics MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier], Pololu Robotics and Electronics MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier], Pololu Robotics and Electronics MinIMU-9 v3 Gyro. Accelerometer. and Compass [L3GD20H and LSM303D Carrier], Pololu Robotics and Electronics
НА СКЛАДЕ
Цена (включая НДС)
1094,00 руб
Наличие на складе
34 шт.
поиск по складам

Заметили ошибку в работе сайта?
Скажите нам об этом