DRV8833 Dual Motor Driver Carrier, Pololu Robotics and Electronics

DRV8833 Dual Motor Driver Carrier Texas Instruments' DRV8833 is a dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2.7 V to 10.8 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 2 A per channel for a few seconds, making it an ideal driver for small motors that run on relatively low voltages. Since this board is a carrier for the DRV8833, we recommend careful reading of the DRV8833. The board ships populated with SMD components, including the DRV8833, and adds a FET for reverse battery protection. This board is very similar to our DRV8835 dual motor driver carrier in operating voltage range and continuous current rating, but the DRV8835 has a lower minimum operating voltage, offers an extra control interface mode, and is 0.1 smaller in each dimension; we also carry a DRV8835 dual motor driver shield that is easy to use with an Arduino. The DRV8833 has a higher peak current rating (2 A per channel vs 1.5 A), optional built-in current-limiting, and no need for externally supplied logic voltage. For a smaller, lower-cost, single-channel alternative to this driver, please consider our DRV8838 carrier, which offers a similar operating voltage range and current capabilities. For higher-voltage alternatives to this driver, consider our A4990 and DRV8801 motor driver carriers. Features Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor Operating voltage: 2.7?? V to 10.8 V Output current: 1.2 A continuous (2 A peak) per motor Motor outputs can be paralleled to deliver 2.4 A continuous (4 A peak) to a single motor Inputs are 3V- and 5V-compatible Under-voltage lockout and protection against over-current and over-temperature Reverse-voltage protection circuit Current limiting can be enabled by adding sense resistors (not included) Features: Motor driver: DRV8833 Motor channels: 2 Minimum operating voltage: 2.7V Maximum operating voltage: 10.8V Continuous output current per channel: 1.2 A Peak output current per channel: 2 A Continuous paralleled output current: 2.4 A Reverse voltage protection: Yes

DRV8833 Dual Motor Driver Carrier, Pololu Robotics and Electronics

Параметры DRV8833 Dual Motor Driver Carrier

НаименованиеDRV8833 Dual Motor Driver Carrier
ПроизводительPololu Robotics and Electronics (POLOLU)

Документация для DRV8833 Dual Motor Driver Carrier

Аналоги DRV8833 Dual Motor Driver Carrier, доступные на складе

  • Изображение  DRV8825 Stepper Motor Driver Carrier

    DRV8825 Stepper Motor Driver Carrier

    Склад (1-2 дн)

    Новый драйвер шагового двигателя DRV8825, который может использоваться как замена драйверу A4988 Stepper Motor Driver Carrier. - Simple step and direction…

  • Изображение  DRV8824 Stepper Motor Driver Carrier

    DRV8824 Stepper Motor Driver Carrier

    Драйвер DRV8824 для микрошаговых биполярных двигателей. The DRV8824 stepper motor driver carrier is a breakout board for TI's DRV8824 microstepping bipolar stepper motor driver, a lower-current version of the DRV8825.…

Сопутствующие товары для DRV8833 Dual Motor Driver Carrier

Цена (включая НДС)
325,50 руб
от 5 шт. 310,50 руб
от 10 шт. 295,50 руб
Наличие на складе
Нет на складе,
сообщить о поступлении
Уведомить о поступлении
поиск по складам

Заметили ошибку в работе сайта?
Скажите нам об этом