Комплектующие для робототехники - Решения

Описание:
The Graphics Display Truly 3.2” 240x320 Board is a demonstration board for evaluating Microchip’s graphic display solution and graphics library for 16- and 32-bit microcontrollers. It is an expansion board compatible with the PIC24FJ256DA210 Development Board (DM240312), and Graphics LCD Controller PICtail™ Plus SSD1926 Board (AC164127-5).
Возможности:

    • 3.2” QVGA (240x320) TFT LCD with 18-bit parallel RGB interface
    • Resistive 4-wire touch screen

Документация:
  • Даташит
  • Тестирование
Описание:
The Graphics Display Prototype Board (set of three) provides an easy path to integrate a graphics LCD panel of developer’s choice to one of the following platforms.
  • PIC24FJ256DA210 development board (DM240312)
  • Graphics LCD Controller PICtail™ Plus SSD1926 Board (AC164127-5)

Возможности:

    • Microchip display connector V1
    • Footprints of flat flexible connectors (FFC) with up to 50-pins with varying pitch sizes (1.0, 0.8, 0.7, 0.6, 0.5 mm), and VESA FPDI-1
    • Prototyping area for power supply circuits
    • Flexible mapping of V1 connector signals to FFC connector signals
    • Compatible with Prototype PICtail Plus™ Daughter Board (AC164126)

Документация:
  • Даташит
  • Схемотехника
Описание:

This product is no longer available for sale.

The temperature sensor demonstration utility allows designers to configure and experiment with Microchip's digital temperature sensors to gain a better understanding of device capabilities. For the devices that have EEPROM, the utility allows reads and writes to the EEPROM, demonstrating the ability to save data and persist it through power events. The utility allows users to adjust temperature limits, modify register settings to see the effects on device operation, and plot real-time temperature data. The utility supports the Microchip AT30TK175STK and ATAVRTempSensorX, and will configure and read the Microchip AT30TS002B, AT30TS75, AT30TS750, and AT30TSE758 temperature sensors. The alarm trip registers toggle LEDs on the board and on front panel of the utility, demonstrating the use of the event pin.

A toggle switch allows the user to manually control temperature to become more familiar with the environment without manipulating the actual temperature of the device.

After installing a kit and verifying the board appears in Device Manager as a serial port, the software should install and launch. A pull-down selection box will show the serial ports available on your machine, one of which should be the serial port to which the board installed, generally COM 4 or higher. When the proper serial port is selected and the board recognized, the other pull-down well allow selection of the chip on the board to communicate with and the proper front panel will launch.

The device datasheet should be available and consulted while using the software to gain an even deeper understanding. The ultimate goal of the utility is to familiarize the user with the datasheet and prepare him to create his own uses.

Возможности:

    A toggle switch allows the user to manually control temperature to become more familiar with the environment without manipulating the actual temperature of the device.

Описание:

The DM080101 Water Tolerant Touch Surface development kit enables easy evaluation of the 2D Touch Surface library. The kit demonstrates water tolerance and noise immunity on a touch pad and has two touch buttons, all controlled by the same MCU.

Возможности:

    • Surface Sensor: 5x6 Surface diamond pattern with dedicated driven shield
    • Two Self-Capacitance Touch buttons
    • ATtiny1617 8-bit AVR Microcontroller - 20 MHz, 16 Kbytes Flash, 2 Kbytes RAM,128 bytes of EEPROM
    • Debugging and Programming: mEBDG with CDC UART
    • LEDs to indicate position and mode
    • LED Driver: MCP23017

Документация:
  • Даташит
  • Топология платы
  • Тестирование
Описание:

The DM0164149 Water Tolerant 2D Touch Surface development kit - PIC Edition enables easy evaluation of the 2D Touch Surface library. The kit demonstrates water tolerance and noise immunity on a touch pad and has two touch buttons, all controlled by the same MCU.


Please be aware of the sister kit (DM080101) offering the same functionality and form factor, running the 2D Touch surface library on a ATtiny1617.

The QT8 Xplained Pro Extension Kit (AC164161) enables you to combine a small touch pad with supported XPRO MCU boards, 8bit and 32bit.

Возможности:

    • Touch Pad: 5x6 surface, diamond pattern with dedicated driven shield
    • Two Self-Capacitance, water tolerant Touch buttons
    • PIC16F18456 8-bit PIC Microcontroller - 32 MHz, 28 Kbytes Flash, 2 Kbytes RAM, 256 bytes of EEPROM
    • Debugging and Programming: PKoB 4 (direct MPLAB and Daa Visualizer support
    • LEDs to indicate position and mode
    • LED Driver: MCP23017

Документация:
  • Даташит
  • Програмное обеспечение
  • Топология платы
  • Тестирование
*Информация о ценах и сроках поставки носит информационный характер. Офертой является только выставленный счет.

Сравнение позиций

  • ()