Каталог решений

forward

Настольный компьютер

Описание:
PMP20107 is a 4-switch buck-boost controler utilizing the LM5175 for consumer applications. This design has a minimum operating input voltage of 3.5V after start up and a maximum input voltage of 30V. Switching frequency is set to 300kHz. A charge pump voltage doubler is added to ensure VCC voltage under low Vin.
Возможности:

3.5V to 30V in, output 5V@ 3A Achieving efficiency of 90% at 3.5Vin and 93% at 20Vin, 95% peak efficiency Compact size, slim form factor, suitable for USB type C dongle Solution Size: 22mm x 19.5mm LM5175 4-switch Buck-Boost controller, wide Vin, high efficiency

Документация:
  • Схемотехника
  • BOM
Описание:
PMP20371 is a synchronous buck boost design utilizing the LM5122 for telecom applications. This design has a minimum operating input voltage of -35V and a maximum input voltage of -60V. Switching frequency is set to 150kHz. The design is built on PMP20371 PCB, 4 layer board with 2oz copper on each layer.
Возможности:

-35V to -60V in, output 14.5V@ 9A Achieving efficiency of 93% across all operating conditions Compact size, slim form factor, suitable for telecom applications Solution size: 48mm x 45mm LM5122 synchronous boost controller, wide input voltage, high efficiency

Документация:
  • Схемотехника
  • BOM
Описание:
PMP20430 is a 4-switch buck-boost controller utilizing the LM5175 for industrial applications. This design has a minimum operating input voltage of 10V and a maximum input voltage of 32V, supports 25Vout @ 1A. Switching frequency is set to 600kHz, during buck-boost mode, switching frequency drops in half, the buck and boost switches at 300kHz alternately with respected max and min duty cycle.
Возможности:

10V to 32V in, output 25V @ 1A Achieving efficiency of 90% across entire operation range, 96% peak efficiency Compact size, slim form factor Solution size: 24mm x 20mm LM5175 4-switch buck-boost controller, wide Vin, high efficiency

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP21098 reference design uses UCC28056 transition mode PFC controller and UCC25630 enhanced LLC controller with integrated driver to provide 12V/10.8A output (continuous, 14.2A peak) from universal AC input. This design achieves 92.4% peak efficiency at 115VAC input and 94% peak efficiency at 230VAC input. The efficiency and power factor numbers also meet both 115V and 230V internal 80 PLUS gold specifications. In addition, the design is able to achieve less than 600mW power consumption with 350mW output power without turning off PFC.

Возможности:

Universal AC input to 12V/10.8A (continuous), 14.2A (peak) Compact 54mm x 141mm x 30mmboard dimension Less than 20% THD with 25% load 94% peak efficiency Less than 600mW power consumption with 350mW load Auxilliary power supply not needed to achieve low standby power

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP9725 reference design generates a 3.3V output from a 12V input, using the TPS562209 synchronous buck converter. This converter uses the DCAP2 control method to minimize output capacitance while eliminating feedback compensation components and still providing an excellent load transient response. The converter switches at 650kHz. The peak efficiency of this design is 90%.

Возможности:

Utilizes DCAP2 control method 90% peak efficiency Small 15mm x 8mm footprint Low profile < 3mm Test report available

Документация:
  • Схемотехника
  • BOM
Описание:
This verified reference design is a two-port, USB 3.0 compliant hub. It provides simultaneous SuperSpeed and high-speed/full-speed connections on the upstream port and provides SuperSpeed, high-speed, full-speed, or low-speed connections on the downstream ports. The hub design provides power control for each downstream port, as well as over-current protection and ESD protection.

Возможности:

Complete dual-port USB 3.0 compliant hub Bus-powered Integrated current limiting ESD protection on all ports Schematic, layout, test data and design documentation for ease of reuse

Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:

Данный протестированный базовый проект представляет собой хаб на 4 порта USB3.0. Возможно устанавливать сверхбыстрые, быстрые и полноскоростные соединения на порте для связи с головным устройством, а также сверхбыстрые, быстрые, полноскоростные и медленные соединения на портах для связи с периферийными устройствами. Дизайн хаба предполагает управление питанием отдельных портов для связи с периферийными устройствами, а также защиту от перегрузки.

 

Возможности:

  • Полноценный хаб на 4 порта USB 3.0
  • Поддержка управления питанием отдельных портов
  • Защита от электростатического разряда как на порте для связи с головным устройством, так и на портах для связи с периферийными устройствами
  • Функционирует при питании как от шины, так и от внешнего источника питания
  • Устройство, поддерживающее USB 3.0 и USB 2.0
  • Схема электрическая принципиальная, трассировка платы, результаты испытаний и конструкторская документация для простоты повторного использования

Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
This TPS65218-based reference design is a compact, integrated power solution for Xilinx® Zynq® 7010 SoC/FPGAs (out of the Zynq® 7000 series family of products). This design showcases TPS65218 as an all-in-one PMIC used to supply the five rails needed for powering the Zynq® 7010 SoC/FPGAs. The total board area needed for TPS65218, including passive components, to supply the five power rails to the Zynq® 7010 is just 1.594 in2. The TPS65218 has the flexibility to support either DDR3L or DDR3 memory. This power management IC can be run from a single 5V supply or from a single cell Li-Ion battery. This design is guaranteed to operate across an industrial temperature range (-40°C to 105°C).

Возможности:

Provides 5 supply rails to power the Zynq® 7010 in a compact 1.594 in2 area (includes passive components) TPS65218 offers 4 highly efficient DC-DC converters with integrated FETs and 1 adjustable general purpose LDO Includes an integrated, programmable sequencer for flexible power-up sequencing On-chip GPIOs can be programmed to power sequence additional discrete components, if needed Qualified for Industrial Applications (-40C to 105C) This design includes a test report, an EVM guide, and design files to help accelerate the evaluation process

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The USB Type-C™ audio adapter accessory mode reference design provides the solution for transmitting analog audio through the USB Type-C interface. This reference design demonstrates how analog audio can be transmitted to system peripherals using the USB Type-C standard audio adapter accessory mode, while still maintaining the ability to transfer USB data over the same USB Type-C connector.
Возможности:

Supports analog audio through USB Type-C connector Low total harmonic distortion (THD) = <-85 dB (0.005%) at 1 Vpp Replaces large 3.5-mm audio jack with smaller Type-C connector Protects microcontrollers from negative voltage swings from analog audio Supports USB Power Delivery

Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
This addapter converts a USB standard host type-A port to Type-C DFP (downstream-facing port) with support for default, 1.5 A and 3.0A VBUS current levels. The TUSB2522 simplifies the design by integrating 2:1 USB 3.1 (up to 10 Gbps) mux with a DFP controller to monitor the Type-C configuration channel (CC) pins to determine plug orientation for mux selection and device attachment for controlling VCONN and VBUS power switches.

Возможности:

Plug and Play design The Reference Design operates off of the 5-V VBUS input from the legacy Type A USB connection The Reference Design can provide VCONN over a CC pin based upon Type C plug orientation and Ra detection DIP switch is provided to configure CC for different Type C current mode operations

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This USB 2.0, USB 3.0 Re-driver Dongle Design connects directly to a Host USB port and re-drives the High-Speed or SuperSpeed signals to the downstream port to enable a long cable connection to a SuperSpeed or High-Speed device.

Возможности:

Plug and Play Design Operates as a bus-powered device not requiring an external supply USB2.0, USB3.0 compatible Supports all system low-power states Compatible with USB On The Go (OTG) and Battery Charging (BC 1.2) protocols Small Design

Документация:
  • Схемотехника
  • BOM
Описание:

Данное типовое решение позволяет оценить реализацию USB Type-C док-станции с поддержкой видеовыхода и зарядки. В USB Type-C док-станции реализованы дополнительные порты данных, видеовыход и возможность зарядки USB Type-C устройств, которые поддерживают альтернативный режим USB PD. Док-станция содержит три USB DFP порта: два Type-C DFP на 5 В и 3 А и один Type-A DFP c поддержкой BC1.2. К разъему DisplayPort можно подключить монитор, MST концентратор или переходник.

Возможности:

  • Питается от 20 В постоянного напряжения
  • Концентратор USB 3.0 на базе TUSB8041 для расширения количества портов
  • Разъем  mini-DP для подключения внешних мониторов, конверторов или концентраторов
  • Несколько светодиодов для упрощения процесса отладки
  • DIP-переключатели для изменения конфигурации решения

Документация:
  • Схемотехника
  • BOM
Описание:
The Front Port Type-C extender reference design connects to an internal motherboard USB3.0 connectors and provides signal conditioning to both High-Speed and SuperSpeed signals to the remotely placed front port Type-C connector. This module enables two fully functional USB Type-C connectors on the internal USB motherboard connector.

Возможности:

Operates from 5V provided from motherboard VBUS not requiring and external supply USB2.0, USB3.0 compatible Supports all system low-power states Enables Type-C connectivity Small Design eases system implementation

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design uses Texas Instrument's SuperSpeed USB 3.0 to SATA bridge, USB Type-CTM and USB PD controller with integrated power switch and High-Speed USB mux, and SuperSpeed USB 3.1 mux to demonstrate the subsystems required to implement a Type-C external hard disk drive capable of delivering power to a Type-C host (laptop, tablet, phone, and more).

Возможности:

USB-IF certified Power Delivery silicon 5V @ 3A or 12V @ 3A power source with optional 5A support SuperSpeed USB 3.0 data transfer rates Serial ATA revision 2.0 (6 Gbps) TRIM support

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The TIDA-00890 Dongle is designed to evaluate HD3SS3220 devices for DFP implementations. This reference design can also be used as a hardware reference design for any implementation using the HD3SS3220 with a USB-C™ connector. The layout files can be used as a guideline to implement the TUSB321A HD3SS3220 with illustrations of the routing/placement rules. The reference design includes on-board USB Type-A plug to connect to legacy USB systems. Please note that the design may include test components for evaluation purposes not applicable for production.

Возможности:

Operates off of the 5V VBUS from the legacy Type A USB connection Can provide VCONN over a CC pin based upon Type C plug orientation and Ra detection Has a USB Type-A plug and a USB Type-C™ receptacle. The Type-A plug can be connected to a USB legacy Type-A receptacle for host side connection. USB3 TX and RX signals are multiplexed through HD3SS3220 to support both connection orientations on the USB Type-C™ port. Small Design eases system implementation

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The TIDA-00891 is designed to evaluate HD3SS3220 devices for UFP implementations. This reference design can also be used as a hardware reference design for any implementation using the HD3SS3220 with a USB-C™ connector. Reference design files can be provided upon request to aid PCB design with HD3SS3220. The layout files can be used as a guideline to implement the TUSB321A with illustrations of the routing/placement rules. The reference design includes on-board USB Type-A plug to connect legacy USB systems. Please note that the reference design may include test components for evaluation purposes not applicable for production.

Возможности:

Operates off of the 5V VBUS from the legacy Type A USB connection USB2 D+1 and D+2, D-1 and D-2 are shorted on the Type-C connector to support both connection orientations Has a USB Type-A plug and a USB Type-C™ receptacle. The Type-A plug can be connected to a USB legacy Type-A receptacle for host side connection. USB3 TX and RX signals are multiplexed through HD3SS3220 to support both connection orientations on the USB Type-C™ port. Small Design eases system implementation

Документация:
  • Схемотехника
  • BOM
Описание:
This display reference design is created for a wide array of ultra-mobile and ultra-portable display applications in consumer, wearables, industrial, medical, and Internet of Things (IoT) markets. The design includes the DLP2000 chipset comprising of DLP2000 .2 nHD DMD, DLPC2607 display controller and DLPA1000 PMIC/LED driver. This reference design can be used with production ready optical engines and low-cost application processors that support 8/16/24-bit RGB parallel video interface in small-form factors.
Возможности:

Most affordable way for developers to incorporate DLP technology in their display applications I2C and 8/16/24-bit parallel RGB video interfaces to support virtually any low cost host processor 5V input and LED current drive up to 1A Affordable and compact PCB layout supporting nHD (DLP2000) optical engine TI Design used in theDLPDLCR2000EVMlayout

Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-03030 reference design provides a robust protection solution for the power path in USB Type-C™ applications. The design protects the power path from overvoltage, overcurrent, hot-plug, and reverse-current events by leveraging the TPS25923 (eFuse) and CSD17571Q2 (reverse-blocking FET). The system solution emulates a downstream facing port (DFP) and is able to detect the connection of an upstream facing port (UFP) device. The TIDA-03030 reference design also supports analog audio for USB Type-C audio accessories. The flexible VBUS protection with audio accessory functionality is achievable within a 20 mmx 20 mm, four-layer, single-sided solution.
Возможности:

Reverse current blocking and overvoltage protection up 30 V Overcurrent events and short-circuit protection Determines UFP connection, audio accessory, port attachment, and cable orientation Automatically switches between analog audio and USB data lines Routes MIC and GND signals automatically

Документация:
  • Схемотехника
  • BOM