forward

Промышленные ИП

Описание:
The PMP10100 reference design uses the LM5023 flyback controller for the Quasi-Resonant Flyback Topology. It generates an isolated output (19.5V@3.84A) from an universal input (85VAC - 265VAC).

Возможности:

Quasi-Resonant Flyback Topology Four Point Average Efficiency = 89.3% (Vin=110VAC) Four Point Average Efficiency = 89.4% (Vin=230VAC) 10% Load Efficiency = 89.6% (Vin=110VAC) 10% Load Efficiency = 87.2% (Vin=230VAC)

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
The PMP10110 design converts the universal input AC voltage to isolated 17V...30V@6A and is suitable to charge lead-acid or Li-Ion batteries. The converter is a constant-V and constant-I genarator and the set points for output voltage (charge level) and current are settable by means of two PWM signals. The first stage is a PFC boost while the isolation ad current stabilization is performed by DC-DC half bridge stage. An isolated quasi-resonant flyback converter supplies all internal voltages and provide some extra current for external loads (fan or analog section), in details 12V@400mA and 5V@300mA.

Возможности:

The first stage is a CCM PFC boost driven with UCC28180, showing high efficiency and low EMI signature The second stage is a DC/DC half bridge, wich includes both current and voltage loops; a PWM signal is used as reference for voltage and current An auxiliary power supply generates all needed voltages; a network is disconnecting all resistors tied to high voltage to reduce stand-by losses Plug-to-plug efficiency at full load: 86%...92% in the whole input voltage range This design is tested and includes test results and CAD files

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
PMP10267 reference design uses the UCC28910 primary side regulation DCM flyback controller to generate 15V/0.25A, 12V/0.25A, and 5V/0.1A triple outputs from high line AC input. Peak efficiency of 75% is achieved in this design.

Возможности:

High line AC input with 15V, 12V and 5V outputs Primary side regulation Flyback with multiple outputs 1.1" x 3" Compact board size Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
The PMP10283 reference design provides 30V/100W and -30V/100W outputs from AC line voltage to a single LLC resonant converter stage. This design is featured with its low circuit cost and high efficiency (over 90% @ 120VAC full load and ~92% @ 240VAC full load). This design uses the UCC25600 resonant converter controller for LLC resonant converter.

Возможности:

88VAC-132VAC or 176VAC-264VAC Input +/-30V 200W output Up to 92% converter efficiency Single stage AC-DC LLC-SRC Low circuit cost

Возможность заказа
  • Заказать BOM
Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10319 referencedesign is a compact and thermally efficient design intended to step down a wide range of AC inputs (85VAC to 265VAC). This non-isolated Buck design incorporates the UCC28710 PSR controller. The PMP10319RevA board are designed with complete standard components (including magnetics).

Возможности:

85VAC to 265VAC, 50/60Hz input 15V/400mA Less than 45o C temperature rise on all parts Utilize all standard components (including magnetics) Compact board size with single layer 1.05" W x 2.1" L layout dimension Test report available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
This design uses the PSR controller UCC28630 that is capable of operating in both CCM and DCM. With the help of X-cap discharge function of UCC28630, the safety discharge resistor can be elimiated. Full load efficiency is 83.5% at 120VAC/60Hz input and 86% at 230VAC/50Hz input.

Возможности:

Universal AC input: 85VAC-264VAC CCM/DCM PSR controller UCC28630 12V/75W rated output No need for additional safety discharge circuits Full load efficiency is 83.5% at 120VAC/60Hz input and 86% at 230VAC/50Hz input

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design generates three separate isolated 12V/0.77A outputs from either an 85-265VAC single phase input or a 200-480VAC-LL three phase input. The UCC28700 controls a flyback converter power stage. The primary side regulation feature of the UCC28700 eliminates the need for an optocoupler, reducing cost and complexity. The three outputs are isolated from each other and can be stacked in series to generate higher output voltages.

Возможности:

Accepts 3 phase input voltages up to 480VAC, as well as single phase 85-264VAC Generates three separate isolated 12V/0.7A outputs that can be stacked in series or in parallel for different output voltages/currents Delivers 25W total output power Start-up time <200ms (at 230VAC or higher), <400ms (115VAC Features 960V N-channel power MOSFET switch Primary Side Regulation eliminates optocoupler, reduces cost, increases reliability

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:

PSR - Primary-Side Regulation, контроль и  регулировка выходного напряжения осуществляется контроллером в первичной цепи. Такая реализация позволяет сократить BOM изделия за счет отсутствия компонентов обратной связи.

Это решение использует для реализации обратноходового преобразователя 12 В/60 Вт PSR контроллер UCC28710. Использование UCC28710 позволяет удешевить конструкцию и добиться максимальной эффективности 84,3% при входе 120 В/60 Гц и 86% при входе 230 В/ 50 Гц.

Возможности:

  • Универсальный вход: 85-265В;
  • DCM PSR контроллер UCC28710;
  • Номинальный выход 12 В/60 Вт;
  • Эффективность при полной нагрузке 84,3% (120 В/60 Гц) и 86% (230 В/50 Гц).

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10385 reference design uses the UCC28910 primary-side regulated flyback controller with integrated MOSFET to generate a 12V/0.3A output from an univeral AC input with safety isolation rated transformer. Over 80% efficiency is achieved at full load and less than 100mW power consumption is observed during no load condition.

Возможности:

Universal AC input with 12V/0.3A output Less than 100mW no load power consumption Over 80% efficiency at full load 1" x 1.38" compact board dimension Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
This design uses low-cost primary side regulation (PSR) IC UCC28700 with a SiC-FET for 200VAC-400VAC input range. A 24V output is generated with maximum 50W rating.

Возможности:

High voltage AC input: 200VAC-400VAC SiC MOSFET utilized 50W Maximum output power rating at efficiency of 86.5% at 200VAC, 86.9% at 400VAC

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10467 reference design uses the UCC28911 primary-side regulated flyback controller with integrated MOSFET to generate a 5V/1.4A output from an univeral AC input with safety isolation rated transformer on a single layer board. About 50degC temperature rise on UCC28911 is observed at full load. It is notable that the power consumption at no load is less than 40mW.

Возможности:

Universal AC input with 5V/1.4A output Less than 40mW no load power consumption MOSFET integrated PSR controller on a single layer board About 50oC temperature rise on the controller at full load Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10535 reference design is a low profile quad output isolated Fly-Buck power supply for industrial applications. The power supply has a synchronous buck regulator, LM5017, and a low profile (6mm) transformer. It generates four isolated outputs of ±5V, ±12V, 75mA each. The LM5017 is a 100V wide Vin, 600mA synchronous buck regulator. The input voltage range of the design is 20V to 32V, making it suitable for 24V input industrial application. The Fly-Buck can regulate the secondary side outputs without opto-coupler or aux winding and is capable of achieving good cross regulation within ±5%. With LM5017's constan on-time control, no loop compensation is required, which simplifies the design and helps reducing the external part count and BOM cost.

Возможности:

Multiple isolated bias power using Fly-Buck, ideal for PLC and industrial applications 2.5W output power, +/-12V, +/-5V @ 75mA each, with LM5017 capable of 7.5V to 100V input Primary side regulation without opto; good cross regulation (within +/-5%) 6mm low profile transformer Constant on-time control; no loop compensation required and fast transient response Circuit board is tested, and the design files and test report are included.

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP10545 is an Isolated Flyback Converter with the primary configured as a buck-boost inverter, using the LM5160 regulator IC. The design accepts an input voltage of 9Vin to 30Vin and provides four isolated outputs of +5.7Vout, each capable of supplying 350mA. The design uses an easily available off-the-shelf transformer, making it a more cost effective design solution.

Возможности:

Primary side regulation without Opto Good regulation, within ±5% No loop compensation required/fast transient response Low BOM count & cost, compact solution size No RC snubber at primary winding

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP10559 is a non-sync isolated Flybuck-boost converter with a negative primary voltage. The power supply has a synchronous buck regulator, LM5160, and a versa pack transformer. The design accepts an input voltage of 18V to 30V, and outputs 30V, capable of providing 0.67A of current to the load, making it suitable for 24V input industrial application. The Fly-Buck topology can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good regulation within ±5%. With LM5160's Constan On-Time control, no loop compensation is required, which simplifies the design and helps reducing the external part count and BOM cost.

Возможности:

Versa pack transformer increase design versatility +30V/0.67A with LM5160 capable of 4.5V to 65V input Primary Side Regulation without Opto, Good Regulation, within +/-5% Constant On Time Control, No Loop Compensation Required, and Fast Transient Response No primary winding snubber is required

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10766 reference design uses Buck converter to convert universal AC input voltage to a 15V/0.11A DC output with UCC28910 controller. Circuit simplicity is achieved with quasi-resonant valley-switching operation and the utilization of Buck topology. Peak 77% efficiency is achieved at full load and no load power consumption of this board is less than 70mW.

Возможности:

Universal AC input with 15V/0.11A output Less than 70mW no load power consumption MOSFET integrated PSR controller applied on Buck topology Less than 20oC temperature rise on the controller at full load Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10767 reference design uses Buck converter to convert universal AC input voltage to a 15V/0.13A DC output with UCC28911 controller. Circuit simplicity is achieved with quasi-resonant valley-switching operation and the utilization of Buck topology. Peak 77% efficiency is achieved at full load and no load power consumption of this board is less than 70mW.

Возможности:

Universal AC input with 15V/0.13A output Less than 70mW no load power consumption MOSFET integrated PSR controller applied on Buck topology About 20oC temperature rise on the controller at full load Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design implements the UCC28630 PSR controller in a flyback power supply. The UCC28630 is capable of operating in both Continuous and Discontinuous Conduction Modes which enables high efficiency while reducing inductor size and cost. Safety standards such as EN60950 require that any X-capacitors in EMC filters on the AC side of the bridge rectifier quickly discharge to a safe level when AC is disconnected. Typically, this requirement is achieved by including a resistive discharge element in parallel with the X-capacitor. However, this resistance causes a continuous power dissipation that impacts the standby power performance. In order to reduce standby power and eliminate the standing loss associated with the conventional discharge resistors, the UCC28630 device incorporates active X-capacitor discharge circuitry. In this design, less than 100mW no load power comsumption and over 88% converter efficiency is achieved.

Возможности:

Utilize UCC28630 CCM/DCM PSR controller Over 86% average efficiency Optimized US line AC-DC power supply design 24V/4A rated output This circuit is tested and includes a test report

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP10852 reference design uses the LM5117, CSD18563 for the high side MOSFET and CSD18532 (x2) for the low side MOSFETs. PMP10852 takes input voltages between 27V to 41V and outputs 180W(12V @15A). The size is very small, total area is 1,200mm2 (30mm x 40mm) solution size. The design is ~95% efficient at full load.

Возможности:

High Power(180W) Wide Vin range (27V-41V) Small size(1200mm2 95% efficient

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10861 uses active clamp forward converter for an isolated 24V to 12V/3.4A conversion. Reverse input connection, output over-current protection, output over-voltage protection, input inrush current limiting circuit are integrated in this board. With wide 9-36V input voltage range, over 89.5% peak efficiency is achieved with 24V input voltage. All the components temperature rise are less than 30oC at full load condition.
Возможности:

24V to 12V/3.4A active clamp forward converter 9V to 36V input voltage range Integrated protections: reverse input connection, output over-current protection, output over-voltage protection Peak 89.5% efficiency with 24V iinput Test report available

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP10912 reference design uses the UCC28630 primary-side regulated controller on a two-switch flyback controller to generate a 24V/6A output from 120VAC input with safety isolation rated transformer. Over 87% efficiency is achieved at full load in this design.

Возможности:

120V+/-15% AC Input and 24V/6A Output PSR controller on a two-switch Flyback topology Over 87% efficiency at full load Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10928 reference design uses the TPS5402 non-synchronous Buck controller along with INA213 current shunt monitor to achieve CC/CV control for an 1.5V/1.5A output from 6-12V input voltage. +/-5% voltage regulation in CV mode and +/-5% in CC mode is achieved in this design. It is notable that this design allow the output voltage as low as 0.4V in CC mode.

Возможности:

6-12V input to 1.5V/1.5A output with CC/CV controls +/-5% voltage regulation in CV mode +/-5% current regulation in CC mode Allow as low as 0.4V output voltage in CC mode 1.65" x 1.8" board dimension Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10937 reference design uses Buck converter to convert universal AC input voltage to a 18V/0.3A DC output with UCC28700 controller. Circuit simplicity is achieved with quasi-resonant valley-switching operation and the utilization of Buck topology. With all components placed within the dimension of 1.05" x 2.1", over 80% efficiency is achieved at full load and no load power consumption of this board is about 150mW.

Возможности:

Universal AC input with 18V/0.3A output About 150mW no load power consumption Over 80% efficiency is achieved at full load Less than 40degC temperature rise 1.05" x 2.1" X-Y dimension Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP10948 is a high-efficiency, high power factor AC/DC power supply reference design using UCC28063 interleaved transition-mode PFC controllers. There are two PFC stages in this design, 750W output power generates from one of the PFC stages and 550W output power generates from the other PFC stage. This design achieve 95.6% efficiency at 120VAC input and 98% efficiency at 220VAC input with over 1300W output power.

Возможности:

Interleaved transition-mode PFC Boost converters for total 1300W output power 95.6% efficiency at 120VAC/60Hz input and 1300W output 98% efficiency at 220VAC/50Hz input and 1300W output Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP10950 is a high-efficiency LLC power supply reference design converting from 380VDC input to 85V/7A and 12V/9.5A outputs. Over 94% efficiency is achieved at 710W full load and over 93% efficiency at half load.

Возможности:

LLC-SRC designed for 330V-400V input and 85V/7A and 12V/9.5A outputs Secondary over current protection circuit is applied in this design for double protection Test report is available 94.2% efficiency at 710W full load

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP10974 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 89% average efficiency. The design also features UCC2463x synchronous rectification controller.

Возможности:

85VAC to 265VAC, 50/60Hz input 5V/10A/50W output Over 89% average 4-point efficiency Over 85% efficiency at 10% load (5W) Less than 40mW standby power losses Protected against output short-circuits

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
The PMP10994 reference design uses Buck converter to convert 120VAC input to a 5V/35mA DC output with UCC28880 controller. With high side MOSFET integrated controller, the total component footprint has been minimized. The temperature rise of this board is less than 10oC at room temperature.

Возможности:

120VAC input to 5V/35mA output No customer magnetic applied MOSFET integrated PSR controller applied on Buck topology Less than 10degC temperature rise on the controller at full load Test report is available

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
PMP11064 is a high-efficiency AC/DC power supply reference design with universal AC input and 20V/20A output. Interleaved transition mode PFC and LLC series resonant converter is applied for 20V/20A main power. A PSR Flyback with MOSFET integrated controller is applied as the auxiliary supply. 91.2% efficiency is achieved at low line and full load. 93.1% efficiency is achieved at high line and full load.

Возможности:

400W PSU with interleaved transition mode PFC and LLC-SRC 91.2% efficiency at 120VAC/60Hz and full load 93.1% efficiency at 230VAC/50Hz and full load 100mm x 200mm board dimension Test report is available Over 20mS hold up time

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP11232 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 89.5% average efficiency. The design also features UCC2463x synchronous rectification controller.
Возможности:

85VAC to 265VAC, 50/60Hz input 5V/6A/30W output Over 90% average 4-point efficiency with 120VAC input Over 89.5% average 4-point efficiency with 230VAC input EMI test data included Less than 40mW standby power losses Protected against output short-circuits

Документация:
  • Схемотехника
  • BOM
Описание:
PMP11236 is a high voltage (105VAC to 440VAC) Buck converter reference design using MOSFET integrated controller UCC28881. 24V/100mA is provided by the UCC28881 Buck converter and followed by a TLV70450 LDO to provide 5V/20mA output. This design is compatible with Class B conduction EMI regulation.

Возможности:

105VAC to 440VAC high voltage input Buck converter with MOSFET integrated controller 24V/100mA and 5V/20mA outputs Conduction EMI verified and test data included Board dimension: W x L = 20mm x 45mm No custom magnetic applied

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
PMP11281 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 88% average efficiency. The design also features UCC2463x synchronous rectification controller.

Возможности:

85VAC to 265VAC, 50/60Hz input, 5V/10A/50W output Over 88% average 4-point efficiency Over 77% efficiency at 10% load (5W) Less than 40mW standby power losses Protected against output short-circuits

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
PMP11282 is ahigh-efficiency AC/DC power supply reference design with universal AC input and 24V/17A output. Interleaved transition mode PFC and LLC series resonant converter is applied for 24V/17A main power. A PSR Flyback with MOSFET integrated controller is applied as the auxiliary supply. 91.98% efficiency is achieved at low line and full load. 94.61% efficiency is achieved at high line and full load.

Возможности:

410W PSU with interleaved transition mode PFC and LLC-SRC 91.98% efficiency at 120VAC/60Hz and full load 94.61% efficiency at 230VAC/50Hz and full load 125mm x 225mm board dimension Test report is available Conduction EMI test results included

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP11303 is high-efficiency AC/DC power supply reference design with universal AC input and 25V/13.5A and 12V/1A outputs. LLC+PFC combo IC UCC29950 is applied for the main power stages with 25V/13.5A output while UCC28730 is applied for the auxiliary power with 12V/1A output. This design has low no load power comsumption (152mW@230VAC) and over 93% peak efficiency. This design also meet 80PLUS Gold requirement for 115VAC Internal power supplies.

Возможности:

Conduction EMI test results included Meet 80PLUS Gold for 115VAC internal power supplies 25V/13.5A and 12V/1A dual outputs 122mm x 200mm board dimension Test report is available Over 98% peak PFC efficiency at high line

Документация:
  • Схемотехника
  • BOM
Описание:
Universal line to 13 volt at 60 watts power supply. This is a synchronous fly back operating in continuous conduction mode using TI's synchronous rectifier controller on the secondary.
Возможности:

Universal line input Synchronous rectification Low cost Low stand-by current

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP15002 is a highly efficient, universal AC input to 5V 3A output reference design for cost-optimized adapter and charger applications. The topology is primary-side regulated quasi resonant flyback with synchronous rectification. With the use of primary-side regulation, it eliminates the need of optical coupler and other external compensation components. This design can pass EN55022 class B conducted and radiated EMI. The efficiency and no-load power consumption of this design meet the EU’s Code of Conduct, Version 5, Tier 2 standard.
Возможности:

Primary side regulation eliminating the need of opto coupler Efficiency meets COC V5 Tier2 and DOE6 with 150m ohm cable Passes EN5022B CE and RE specifications with only 100p Y-cap Synchronous recitifcation works with primary side regulation <75mW no-load power consumption

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP11405 reference design uses the UCC28740 constant current (CC), constant voltage (CV) flyback controller for a 5V/1A, 12V/0.9A bias supply with high line AC input (185VAC to 260VAC input). With safety isolated, Over 80% efficiency is achieved at full load and less than 400mW power consumption is observed during no load condition.
Возможности:

High line AC input to 5V/1A and 12V/0.9A dual-output 1.45" x 4.45" board dimension CC & CV is enabled with UCC28740 flyback controller Less than 400mW no load power consumption Cross regulation tested

Документация:
  • Схемотехника
  • BOM
Описание:
PMP20468 is an isolated flyback converter utilizing the LM5022 controller for Power-over-Ethernet applications. This design has a minimum operating input voltage of 36V, a maximum input voltage of 57V, and an output of 12V @ 2A of load current. Switching frequency is set to 420kHz. A custom Wurth transformer is used in this design.
Возможности:

36V to 57V input, 12V @ 2A output LM5022 controller for an isolated flyback topology to achieve over 89% efficiency over all operating conditions Compact size, slim form factor, suitable for power-over-ethernet camera applications Solution size: 81mm x 38mm 91% peak efficiency

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP40228 is a reference design for 5V 2A adapter applications. The solution implements a high efficiency primary side controller UCC28704, it meets COC V5 Tier2 2016 specification with 130mOhm cable, it is fully test and passes conduction EMI. The board uses a single layer PCB and diode rectifier, it is a cost-effective solution with Low BOM cost. The board measures 41mm x 38.5mm x 15mm.
Возможности:

Diode rectifier QR flyback with primary side regulation Single layer PCB Cost-effective solution with low BOM cost High 4-point average efficiency above 79.9% with 130mOhm cable, above 76% efficiency at 10% load Compliant with EN55022 class B conducted EMI Size 41mm x 38.5mm x 15mm

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.

Возможности:

High Efficiency up to 95.8% LM5113+ GaN Mosfets Protection feature OCP, OVP Full Digital Control for HSFB DC-DC Good thermal performance with Full Load Full comply with the telecom customer requirements

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP5315 reference design provides and isolated 14V at 6.5A from a universal AC input. The UCC28600 flyback controller used in this design reduces standby power consumption to less than 250mW by operating in burst mode at light loads, and provides efficiency over 88% at heavier loads by reducing switching losses through quasi-resonant valley switching.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP5322 reference design provides and isolated 14V at 4.7A from a universal AC input. The UCC28600 flyback controller used in this design reduces standby power consumption to less than 200mW by operating in burst mode at light loads, and provides efficiency over 87% at heavier loads by reducing switching losses through quasi-resonant valley switching.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
A 12V-20V input, 95W, five (5) rail design for a PET Scanner control board with the TPS40303/304 PWM step-down controllers and Dual-Cool CSD16322Q5C NexFETs powering DDR core, DSP core, and analog circuitry like detectors, front-end amplifiers/filters and Analog-to-Digital Converters.

Возможности:

92% Efficiency Frequency Spread Spectrum (FSS) to reduce EMI noise peaks 3% voltage regulation tolerance 25degC to +85degC Operating Temperature Range 300KHz/600KHz Switching Frequency 600mm2 total power supply area per voltage rail

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP5761 is designed for hybrid filber/coax system with nominal 40VAC-90VAC input and generate a 24V/3.5A output. A cascade PFC and LLC-SRC two stage system is applied in this design to guarantee high power factor is achieved in nominal input range. Transition mode PFC controller UCC28051 and resonant converter controller UCC25600 are applied to PFC and LLC-SRC, respectively. With PFC output set to 300V, PMP5761 is able to keep out in regulation with input up to 200VAC. 80% converter efficiency is achieved at 40VAC and 87% converter efficiency is achieved at 115VAC.

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP5967 reference design provides a 12V/38A output with over 94% efficiency from a 380VDC input. This design uses the UCC25600 to control the resonant LLC converter. The UCC24610 synchronous rectifier controller is used to control two banks of CSD18501Q5A MOSFETs, eliminating the need for heat sinks on the output rectifiers.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP6570 reference design uses the UCC28050 transition mode PFC controller to generate an isolated 5V/2A output from a universal 90VAC to 300VAC input. This design combines both power factor correction and output regulation in a single stage. In addition, the UCC24610 is used to control a synchronous rectifier on the secondary side of the isolation boundry, improving efficiency.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design provides a compact power solution for 70W (peak) audio systems. This supply accepts a universal AC input, and uses a UCC28610 quasi-resonant flyback controller to generate an isolated 24V. Auxiliary 5V/1.5A and 3.3V/0.1A outputs are also provided. This design is capable of providing power to sustained loads of 30W and peak power loads of 70W with efficiencies up to 85%.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP6740 reference design provides 12V at 18W from a universal AC input of 90VAC-265VAC input. This design uses the TL2844 controller with primary side regulation (no optocoupler) for a low cost power solution.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP6910 reference design delivers an isolated 55V at 2A with PFC from a universal AC input. This design is a modified version of the UCC28600 EVM. The PFC boost portion of the design is unchanged from the original EVM. The UCC28600 quasi-resonant flyback has been modified for the higher output voltage. The flyback portion of the design is over 88% efficient. The total input-to-output effciency of the design is 83% from a 120VAC input and 85% from a 240VAC input. For sustained loads over 1.5A, forced air cooling is recommended.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP6997 reference design uses TPS40400 & CSD86350Q5D to to power a Synchronous Buck Converter. Electrical and Thermal test results shown for 12Vin 1.2Vout at 20A. An on board dynamic load allows rapid load transients to be tested. An on board TLC555 timer can demonstrate external synchronization.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design uses the UCC28600 quasi-resonant flyback controller to generate isolated +12V/250mA and -12V/10mA outputs from a universal AC input. The energy saving features of the UCC28600 minimize power losses at no load and full load conditions. This design is laid out on a 36mm X 46mm printed circuit board.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This 600W wide voltage input dual phase power converter uses two emulated current-mode controllers 180 degrees out of phase to minimize input and output ripple current. Compared to conventional isolated power converters, this synchronous buck architecture provides a reduced footprint and BOM cost at higher levels of efficiency, greater than 97% over several operating conditions.

Возможности:

Two-phase buck converter 600W output power 35V to 60V maximum input voltage range Output voltage of 12V at 50A This reference design board is tested and supported with design files and an application note

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design uses the BQ24640 super cap charging controller to charge a large bank of super caps to a voltage below the input bus voltage. During an input bus dropout, the energy from the super caps is used to power a boost converter that can supply 10A of output current at 26.2V. This output can be used to hold up the bus voltage for up to 10 seconds (260W for 10 sec).

Возможности:

Boost Converter efficiency greater than 95% at Vin = 18V and 1A - 10A loads Boost holdup supports 28V bus for longer than 27 seconds using a large 28F super cap bank while delivering 260W Super cap charger provides a constant 3A charge current for a controlled startup time Low cost design requires less than 100mm x 100mm

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7361 is an isolated flyback converter with a 54V/1.1A output. The 18-60VDC input is suitable for 24VDC industrial and 48VDC telecom applications. The 54VDC output can be used to power PoE power sourcing equipment (PSE).

Возможности:

Efficiency of 93% with 48V input and maximum load Good line/load regulation with optocoupler feedback Wide input range 1500Vrms isolation for telecom or PoE Optional capacitors to provide hold up time

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
This reference design uses the UCC2894 to control an active clamp forward converter that generates an isolated 24 V at 7 A from a 380-VDC input. This supply is intended to be used with a PFC boost front end and requires an external 12-V bias voltage for housekeeping on the primary side. This supply is up to 91% efficient at full load.

Возможности:

91% efficiency Clamped drain voltage for reduced emissions Compact form factor 64 mmx 90 mm (2.5 inx 3.5 in)

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design generates an isolated 12V/160W output from a high voltage DC input. This design is intended to operate from the output of PFC front end regulator. The UCC2897A is used to control an active clamp forward converter. Texas Instruments CSD18531Q5A synchronous rectifiers allow this design to achieve over 92% efficiency. An accurate current limit is provided by directly sensing the output current. A clock pulse output is also provided for synchronizing with other converters.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

В данном базовом проекте из высокого постоянного входного напряжения генерируется изолированный выход 5 В (100 Вт). Данный проект разработан для функционирования от выхода аппаратного средства регулятора ККМ. Для управления однотактного прямоходового преобразователя с активным демпфером используется UCC2897A. КПД 91% достигается благодаря использованию самовозбуждающихся синхронных выпрямителей. Точное ограничение тока осуществляется за счёт измерения выходного тока. Также доступен выходной тактовый импульс для синхронизации с другими преобразователями.

 

Возможности:

  • Преобразования из 220-400 В постоянного напряжения в 5 В/ 20 А (100 Вт)
  • КПД 91 %
  • Измерение выходного тока
  • Используется контроллер UCC2897A совместно с синхронными выпрямителями семейства NexFET от TI
  • Топология однотактного прямоходового преобразователя с активным демпфером
  • Уменьшенные потери на проводимость, а также площадь посадочного места синхронных выпрямителей

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7758 is a non-synchronous buck DC-DC controller with 6-20V DC input and 3.3V @ 1A output. It is a low cost, efficient switching regulator. It uses LM25011 which contains an N channel buck switch, a startup regulator, current limit detection, and internal ripple control. The constant on-time regulation principle requires no loop compensation, results in fast load transient response, and simplifies circuit implementation.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7760 is a high voltage flyback DC-DC converter with Q100 and D100 qualification. The design includes an external bias supply to withstand 800V. LM5022 used in the circuit has additional features like an error amplifier, precision reference, line under-voltage lockout, cycle-by-cycle current limit, slope compensation, soft-start, external synchronization capability and thermal shutdown.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Типовое решение PMP7763 – высоковольтный изолированный DC/DC преобразователь. Входное напряжение от 30 до 800 В, выходное – 24 В 250 мА. Во вторичной части схемы не реализована обратная связь по выходному напряжению. Контроль выходного напряжения реализован в первичной части схемы.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7764 is a non-isolated flyback converter. The input voltage ranges from 30 – 800V DC. The output is 20V @ 250mA. It has a high voltage hold off circuit.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
Circuit is a non isolated flyback converter. Vin is 700V to 800V max, converting to 16.5V out at a maximum current of 500mA. The design utilizes an external Error amplifier using an LMC7101 for feedback control. The circuit also uses U102 and Q101(and resistors etc etc…) as an external UVLO circuit. LM5021 features include an ultra-low (25 µA) start-up current, which minimizes power losses in the high voltage start-up network. A skip cycle mode reduces power consumption with light loads for energy conserving applications.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP7800.1 reference design is a Buck which uses a LMR14203 and was intended for Computers and Peripherals applications. It can generate a Non-Isolated 3.3 volt output at 0.07 Amps from an input 21.6 to 26.4 Volts DC.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This is a non-synchronous buck converter design that has an input voltage range of 18V-to-32Vin max and provides a regulated output of 13.5Vout@15A.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
A 12V nominal OR-ing circuit design, allowing users to select one of the two input supplies to be directed as the power supply to a system.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7902 is an Isolated Flyback converter utilizing the LM5001 non-synchronous current-mode regulator I.C. The design accepts an input voltage of 4.5V to 5.5V and provides an isolated 5V output capable of supplying 0.25A of current to the load. The design uses an off-the-shelf VERSAPAC transformer, providing 500V of operational isolation between primary and secondary. A precision shunt regulator provides a tight control of the output voltage using an optocoupler to cross the isolation barrier.

Возможности:

Isolated output Uses standard off-the-shelf transformer Regulated output using precision shunt on secondary Low-profile design using all ceramic capacitors Integrated switching MOSFET Built-in over-current protection

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7932 is an isolated flyback converter which accepts an input voltage of 12Vin to 24Vin and provides dual polarity ouputs of +12Vout @ 0.25A and -12V @ 0.25A.

Возможности:

Ease of use with off the shelf transformer Internal MOSFET Split rail bias supply Isolated input/output for safety Small solution size 300kHz and 700kHz frequency options Cycle-by-Cycle current limit Small device package size Dmax of 90% Excellent line and load regulation

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Изолированный обратноходовой преобразователь с постоянным высоким входным напряжением (диапазон от 300 В до 600 В) и изолированным выходом 20 В при токе 1,5 А.

Данный базовый проект имеет характер аппаратного решения.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
A Flyback design accepting an input voltage of 4.5Vin to 5.5Vin and providing an isolated output of 4Vout that can deliver 0.7A.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The following design is a 60W Flyback which uses the UCC3809 and the UCC39002. It creates a 12V@10A output by employing dual 12V@5A. The system functions in the continuous conduction mode.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
Low EMI, high efficiency, high power factor and reliable power supply are main focus of the PMP8911 design for telecom applications. Transient mode (TM) power factor correction (PFC) with UCC28051 and LLC series resonant converter (SRC) with UCC25600 are applied in PMP8911. Low EMI is expected with zero voltage switching on TM-PFC and LLC-SRC switches. An overall 92% efficiency is achieved at 100W full load. In addition, several protections are embedded into this design which includes input under-voltage protection, input over-voltage protection, output over-voltage protection, and output hic-cup over-power protection.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Типовое решение PMP8920 – надежный и эффективный источник питания с низким EMI и высоким коэффициентом мощности, предназначенный для применения в сфере телекоммуникаций. Переходной режим (TM) коррекции коэффициента мощности (PFC) на базе UCC28051 и LLC резонансный преобразователь (SRC) на базе UCC25600 применялись ранее в решении PMP8911. В данном решении дополнительно после LLC используется синхронный выпрямитель UCC24610. Низкий уровень EMI достигается за счет переключения TM-PFC и LLC-SRC при переходе напряжения через 0. Общий КПД достигает 91% при полной нагрузке 100 Вт. Дополнительно в данное решение встроена защита от повышенного и пониженного напряжения на входе, повышенного напряжения на выходе и защита от перегрузки выхода.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP8930 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 20V output from a univeral AC input. a bulk capacitor with slow-charge-fast-discharge circuit is placed at flyback output to provide long hold up time for the following step-down DC-DC stages. TPS54335 is used as the controller and power stage for the main 4V or 12V output. The valley switching of the UCC28710 allows this low-cost design to achieve a maximum load efficiency of 83%; no load losses are less than 70mW.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP9041 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 24V/40W output from a univeral AC input. The valley switching of the UCC28710 allows this low-cost design to achieve a maximum load efficiency of 90%; no load losses are less than 50mW.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This 4W reference design generates both a 3.3V and 12V output. The 3.3V output is regulated, while the 12V output has some load dependent variation. The UCC28740 flyback controller provides a low cost yet efficient solution.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The LM5119 controller allows the user to have two separate regulated outputs or the capability to combine the outputs (of the same voltage) into a two-phase regulator. This design operates from a 36V - 51V input and regulates 28V@2A (with transients up to 7A) and 16V@4A (with transients up to 6A).

Возможности:

Allows for dual or single regulated outputs 36V - 51V input Greater than 96% efficiency Sequenced output voltage Board length is approximately 69 mm Test report is available

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP9243 reference design uses the UCC28720 primary-side regulated flyback controller to generate a 15V/0.25A output from an industrial AC input (up to 583VAC). A bipolar transistor is used as the switch on the primary side to minimize the circuit cost.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP9409 reference design is an 4-output isolated Fly-Buck power supply for PLC applications. It takes 24V nominal input and provides 4 isolated sets of (+15V) bias voltage, Each rail has a load of 30mA. Each set of rails is generated from one single transformer windings on the secondary side. A compact solution size is achieved (56x43mm). The design features the LM5017 synchronous buck converter configured as a Fly-Buck regulator. With the benefit of primary side regulation, the supply has the outputs regulated without the opto-coupler or additional transformer winding. The LM5017 has a wide Vin range which is up to 100V and 600mA output current capability with integrated switch FETs. The input voltage to the reference board can be loosely regulated with a range of 17V to 36V.

Возможности:

Four isolated outputs, 4x(+15V@30mA) Fly-Buck converter design, primary side regulation, compact solution for multiple isolated output supply Wide input voltage range of 17V to 36V 85% peak efficiency. LM5017 sync buck regulator, up to 100V wide Vin range, 600mA capability This circuit board is tested, and the design files and test report are included.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Высокие КПД и коэффициент мощности, а также надёжность источника питания – вот главные акценты проекта PMP9531 для применения в драйверах двигателей. В проекте PMP9531 применены корректор коэффициента мощности (PFC) UCC28051, работающий в переходном режиме (TM), и последовательный резонансный преобразователь подуровня логической связи UCC25600. Кроме того, в качестве источника смещённого напряжения использован понижающий преобразователь с включением на верхней стороне UCC28710. На высоком уровне сигнала достигается КПД преобразования 93 %, в то время как на низком уровне сигнала сохраняется КПД преобразования 90 %.

Возможности:

  • Универсальный вход (85-264 В переменного напряжения);
  • Выход 28 В / 350 Вт;
  • КПД преобразования до 93 %;
  • Выходная мощность PFC в режиме TM доходит до 385 Вт;
  • Понижающий AC/DC-преобразователь с включением на высокой стороне в качестве источника смещённого напряжения.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Эта схема реализует горячую замену с использованием контроллера горячей замены с ограничением мощности TPS2490 и двумя 30-вольтными NexFET CSD17570Q5B. Система может использоваться в серверах безопасности для подключения линейных карт во время работы системы. Постоянный ток запуска, контролируемый dV/dt управлением, поддерживает пусковые токи 1 А и 2 А. Схема может быть размещена на линейной карте. Входное напряжение 12 В, ток 60 А.

 

Возможности:

  • Законченное протестированное решение;
  • Подходит для серверных приложений;
  • Возможность обеспечить до 30 В, 0,56 мОм (типовое при 10 В);
  • CSD17570Q5B в корпусе QFN5х6 мм.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Высокие КПД и коэффициент мощности, а также надёжность источника питания – вот главные акценты проекта PMP9640 для применения в драйверах двигателей. Для безмостового ККМ в первом каскаде преобразования PMP9640 применён недорогой аналоговый контроллер ККМ в переходном режиме (TM) UCC28051. Во втором каскаде преобразования PMP9640 применён последовательный резонансный преобразователь (SRC) подуровня логической связи UCC25600. Кроме того, в качестве источника смещённого напряжения использован понижающий преобразователь с включением на верхней стороне UCC28710. В данном проекте КПД безмостового ККМ может достигать 98,5 %.

 

Возможности:

  • Универсальный вход (85 - 264 В переменного напряжения)
  • Выход 28 В/ 310 Вт
  • КПД ККМ до 98,5 %
  • Выходная мощность ККМ в режиме TM доходит до 365 Вт
  • Понижающий AC/DC-преобразователь с включением на высокой стороне в качестве источника смещённого напряжения

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
24V Output, Constant Voltage / Constant Current, 65W Flyback power supply with 130W surge capability. Primary side regulation eliminates feedback opto-coupler and provides 1% regulation down to no-load. Average efficiency of > 89% and no load power of < 70mW are achieved. Voltage input range is 85VAC-265VAC Input.

Возможности:

Primary Side Regulation (PSR) +/- 1% Voltage Regulation +/- 7.5% Current Regulation <70mW Stand-by Power Short Circuit Protection High Voltage Startup > 85% Efficiency at 10% load

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This two-phase synchronous buck operates from 24VDC and supplies an output of 15V@20A. Operation at 300KHz (per phase) delivers small size and greater than 96% efficiency.

Возможности:

Efficiency approaches 97% at 12A load Board length is approximately 94 mm Reduced component size due to two phase operation Test report available

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP9730 reference designemploys the UCC28051 power factor correction controller to implement a single stage PFC-Flyback AC/DC converter that generates an isolated 12V output at 3A from a universal AC input. The design features UCC28910 primary side regulation Flyback switcher for generating the VDD bias rails and the UCC24610 for 2ndary side synchronous rectification. This provides an excellent solution for systems such as motor drives requiring an isolated bus voltage, good power factor and high efficiency.

Возможности:

89% 4-pt average efficiency 90% peak efficiency >0.85 Power factor at 100% load No aluminum capacitors for small size and high reliability Small form factor 50mm X 50mm x 18mm (2" X 2" X 0.7")

Документация:
  • Схемотехника
  • BOM
Описание:
PMP9750 is a CLL resonant converter reference design with 400VDC input and 28V/9A ouput. Unlike LLC series resonant converter, CLL resonant converter used in PMP9750 utilizes its output inductor to minimize the size of the resonant tank. With resonant controller UCC25600 and bridge driver UCC27714, PMP9750 is able to achieve 95.7% peak efficiency.

Возможности:

400VDC input to 28V/9A output Utilize compact, high efficieny CLL resonant converter Test data included Board dimension: W x L x H = 2.05" x 3.8" x 1.21" Achieve 95.7% peak efficiency

Документация:
  • Схемотехника
  • BOM
Описание:

TIDA-00200 - референс дизайн, предлагающий сдвоенную обратноходовую топологию для решений по заряду батарей, которые требуют уровень выходной мощности около 200 Вт при минимальном использовании электронных компонентов. Помимо реальных электронных компонентов одной из основных причин увеличения общей стоимости проекта являются усилия, затраченные на её охлаждение. Используя преимущества высоковольтного сдвоенного контроллера тока LM5032, решение достигает потрясающей эффективности 90% при полной нагрузке и, в то же время, рассеивает тепло для уменьшения затрат на охлаждение. В большинстве случаев вентилятор для охлаждения не требуется, а использование компактных радиаторов обеспечивает дополнительную гибкость решения.

 

Возможности:

  • Вход: 110 В-120 В, ±10%, частота переменного напряжения 50/60 Гц;
  • Выходное напряжение: 21 В (5 Li-Ion батареек), ток заряда до 9,5 А;
  • Эффективность 90%;
  • Перемежающаяся обратноходовая топология, основанная на высоковольтном сдвоенном контроллере тока LM5032;
  • Программируемая блокировка питания при пониженном напряжении, пошаговое ограничение тока;
  • Обратная связь на основе двухканального операционного усилителя с однополярным питанием TLC272.

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:

Высокопроизводительный индикатор тока на основе шунта используется для измерения напряжения протекающего через измерительный резистор, когда через него проходит ток. Дополнительно реализуется внешняя схема защиты от пульсаций и быстрых переходных процессов, демонстрируют различные уровни противодействия в соответствии EC61000-4-4 и IEC61000-4-5.

Возможности:

  • Способность поглощать пульсации в соответствии с требованиями IEC-61000-4;
  • Способность поглощать пульсации в соответствии с требованиями IEC-61000-5;
  • Выбор коэффициента усиления:
    • INA210: 200 V/V
    • INA211: 500 V/V
    • INA212: 1000 V/V
    • INA213: 50 V/V
    • INA214: 100 V/V
    • INA215: 75 V/V

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-00367 is a 150 W flyback converter based reference design created for powering low voltage BLDC motor based applications using a companionTI Design TIDA-00447, 24V Dual Brushless DC Motor Drive Reference Design for Major Home Appliances. This reference design is a primary side regulated flyback converter based on the UCC28630 controller. It works in either discontinuous conduction mode (DCM) or continuous conduction mode (CCM) depending on the input voltage conditions and delivers a tightly regulated 24V output and a loosely regulated 12V output.Primary Side regulation helps in eliminating the use of secondary side feedback components without impacting the performance thereby reducing BOM count and increasing the reliability of the design. The hardware is designed and tested to pass the EN55011 Class B conducted emission and Surge Norm EN – 63000-4-5 .

Возможности:

150W Flyback designed for operating in the wide input range from 85Vac-270Vac. High efficiency of 86% at full load. Low Standby power consumption of 200mW at 230-VAC. Built-in active X-Capacitor Discharge Function to meet SELV limits and eliminates the use of external bleeder resistor. Primary Side Regulation in both DCM and CCM mode of operation. Robust Power stage with built in protection for Overcurrent, Overvoltage, Over-temperature, AC Line UV, Brownout. Meets the requirements of Conducted Emissions standard – EN55011 class B. Fully Tested and Validated to deliver up to 150W and power a low voltage BLDC motor using a companion motor drive board TIDA-00447

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:

Данный источник питания на базе мостового LLC резонансного преобразователя с фазовым сдвигом позволяет работать с малыми нагрузками и низким выходным напряжением. Данный режим работы может заменить режим PWM в LLC, что позволяет повысить эффективность источника питания при низких нагрузках.

 

Возможности:

  • Динамическое переключение между режимами работы с фазовой и частотной модуляцией;
  • Поддержка ZVS в более широком рабочем диапазоне;
  • Управление мощностью в широком рабочем диапазоне.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
Many systems require a backup battery to provide power in the event of a power outage. Switching between the main power and the backup battery power without incurring significant efficiency degradation or cost is a tricky challenge. This design provides a high accuracy, low current solution for systems using a 12 V rail with a backup battery at a lower cost than existing devices.

Возможности:

Low current consumption in battery backup mode: 28 uA High voltage threshold accuracy: 1.75% including resistors Independent voltage programming on primary and secondary rails

Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
DC-DC power converter with digital control using UCD3138CC64EVM-030 daughter-card. The daughter-card with preloaded firmware providing the required control functions for a Phase Shift Full Bridge converter. The TIDA-00412 (UCD3138PSFBEVM-027) accepts a DC input from 370 to 400 VDC, and outputs a typical 12 VDC with full-load output power at 360 W, or full output current of 30 A.

Возможности:

Peak Current Mode Control w/ Internal Slope Compensation & Programming Blanking Time Excellent Voltage Regulation with low jitter for excellent Vout ripple control Oversampling Function for Enhanced Transient response Fully programmable dead-band for optimizing efficiency Dynamic dead time adjustment.

Документация:
  • Схемотехника
  • BOM
Описание:

TIDA-00443 является 900 Вт корректор коэффициента мощности для питания BLDC/PMSM двигателей. Этот дизайн реализован на основе с использованием PFC контроллера UCC28180 со всеми необходимыми средствами защиты. Решение поддерживает широкий диапазон входных напряжений 190 В…270 В, обеспечивая высокую эффективность более 97% при широком диапазоне нагрузок 50%...100%.

Конфигурация повторителя в TIDA-00443 обеспечивает снижение потерь при переключении в PFC регуляторе, а так же в выходном инверторе преобразователе. В сравнении с операциями с постоянным напряжением, этот повышающий повторитель сохраняет дополнительную мощность 5,2 Вт при 230 В переменного тока и полной нагрузке.

Дизайн TIDA-00443 был разработан в соответствии с требованиями IEC-61000-2-3 ограничений iTHD класса А и класса D. В дополнение, дизайн улучшает общую производительность системы с более низкой пульсацией шины, более низким током и встроенной защитой. Аппаратное обеспечение полностью протестировано в соответствии с требованиями EN55014 для бытовой техники.

Возможности:

  • Широкий диапазон входных напряжений: 195 В… 270 В;
  • Спроектирован для управления широким диапазоном инверторных двигателей и понижащих DC-DCпреобразователей до 900 Вт;
  • Высокий коэффициент мощности > 0,99 и менее чем 5% коэффициент гармонических искажений от средней до полной нагрузки. Соответствует действующим нормам THD в соответствии с IEC-61000-3-2 класса А и класса D на 10% и 100% нагрузки.
  • Высокая эффективность более 97% при полной нагрузке во всем диапазоне рабочих напряжений, исключает необходимость внешнего охлаждения при температуре окружающей среды до 55 °C;
  • Встроенная возможность повышающего повторителя  обеспечивает улучшенную эффективность ~98%;
  • Соответствует требованиям EN55011 и IEC6100-4-5.

 

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-00477 reference design is a continuous conduction mode boost converter implemented using TI digital power supply controller UCD3138A and with all the necessary protections built-in. TIDA-00477 PFC is designed to improve overall system performance with lower bus ripple, lower bus capacitance, and lower RMS currents than traditional PFC power supplies. In addition, the design provides precise information of the input energy consumption of the unit. Hardware is designed and tested to pass conducted emissions, surge, and EFT as per EN55014 – requirements.

Возможности:

Wide operating input range 195-VAC to 270-VAC Designed to drive wide range of downstream DC/DC converters and inverter fed motors up to 1kW High power factor > 0.99 and less than 5% THD from medium-to-full load (50-100%). Meets Current THD regulations as per IEC 61000-3-2 High efficiency of > 97% at full load over entire operating voltage range. It eliminates need for external cooling up to 55oC ambient operation for loads ≤ 850W Communicates the input power consumption information of the unit precisely for all load conditions. Built-in 12V/3W supply for house-keeping power needs PMBUS & Isolated UART for communication Meets the requirements of Conducted Emissions standard – EN55011 class A, EFT norm IEC6000-4-4, and Surge norm IEC61000-4-5 Power supply designed with a simple, small PCB form factor (165 x 95mm)

Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area by placing the output inductor on top of the IC and results in 92% minimum efficiency for 66W and 100W output power designs (3.3V and 5V output) requiring only 4x100µF ceramic output caps.

Возможности:

94% Efficiency at 12VIN, 5Vout,20A output current, 650KHz 6W power loss at 100W Output Power 14mV Output Voltage Ripple at 20A output current Only 4x100µF output ceramic capacitors 27mV Output Voltage Overrshoot in response to 5A to a 10A load increase, 2.5A/µs 58.7°C IC case temperature at 5Vout and 20A output current (100W Output Power)

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Данное типовое решение – LLC резонансный полумостовой DC/DC преобразователь с цифровым управлением через дочернюю плату 3138ACC32EVM-149. Дочерняя плата с предустановленным встроенным программным обеспечением реализует функции управления, требуемые для LLC резонансного полумостового преобразователя. Постоянное напряжение на входе TIDA-00512 (3138ALLCEVM-150) от 350 В до 450 В, номинальное напряжение на выходе 12 В при максимальном токе 29 А, выходная мощность при полной нагрузке 340 Вт.

 

Возможности:

  • Синхронный выпрямитель
  • Оптимальная эмуляция диодов и Dead-Time в синхронном выпрямителе
  • Ограничение тока в соответствии с рабочим циклом
  • Автоматическое переключение между режимами LLC и PWM
  • Контрольные точки для облегчения процесса тестирования топологии

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This is a high efficiency 65W AC/DC design for a Universal input (85Vac to 265Vac) to 19.5V @3.33A output exceeding CoC-5 Tier2 and DOE Level VI requirements for external power supplies using the LM5023 Quasi-Resontant Flyback Controller with UCC24630 Synchronous Rectification Controller and CSD19531Q5A MOSFET. Additionally the LM8364 reset controller is used to provide input line AC UVLO protection. As seen at APEC

Возможности:

91.49% @115V, 89.81% @230V 4-point average efficiency 83.14% @120V, 82.24% @230V 10% load efficiency 59mW No-load Power consumption 59mW at high line (230V) Fast turn-on time 75mV output ripple AC line input UVLO protection

Документация:
  • Схемотехника
  • BOM
Описание:
TIDA-00701 is a 100W, 24V, Industrial AC-DC power supply designed for use in Industrial & Instrumentation systems such as process controls, factory automation and machinery control. This reference design has front end Power Factor Correction (PFC) circuit designed using UCC28051 PFC controller, followed by Quasi-Resonant flyback converter implemented using UCC28740 Primary Side regulated (PSR) CC-CV flyback controller, with all the necessary protections built-in. Hardware is designed and tested to pass conducted emissions, surge, and EFT requirements. The key highlights of this reference design are: Reduced component count design to achieve NEC Class-2 and Limited Power Source (LPS) norms Meets Energy Star Rating and 2013 EU eco-design directive Energy-related Products (ErP) Lot 6 Meets stringent current THD norms Robust output supply protected for output over-current, output short circuit, output over-voltage, and over temperature conditions

Возможности:

Wide operating input range 85-VAC to 265-VAC, with full power delivery over entire range. Designed to drive wide range of downstream 24V Industrial systems and motor drives up to 100W. High efficiency of 88% at 115VAC and >89% at 230VAC for wide load range from 40% to 100% load. No external cooling needed up to 60oC ambient operation High power factor >0.97 at both 115VAC and 230VAC for 100% load. Meets Current THD regulations as per IEC 61000-3-2, Class-A. Precision current limit within ±1% ensures maximum power delivery for entire AC input voltage range. Very low standby power of < 200mW. Start-up with high load capacitance up to 8500uF Built-in loss-less ORing feature for paralleling multiple modules Meets the requirements of Conducted Emissions Standard – EN55011 class B, EFT norm IEC6000-4-4 –Level-3, and Surge norm IEC61000-4-5 –Level-3.

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-00702 is a 60-W, industrial AC-DC power supply designed for use in industrial and instrumentation systems such as process controls, factory automation, and machinery control. This reference design is a Quasi-resonant (QR) flyback converter implemented using the UCC28740 CC-CV flyback controller with optocoupled feedback for voltage and primary-side regulation (PSR) for constant current regulation, with all the necessary protections built-in. Hardware is designed and tested to pass conducted emissions, surge, and EFT requirements. The key highlights of reference design: Reduced component count design to achieve NEC Class-2 and Limited Power Source (LPS) norms Meets Energy Star Rating and 2013 EU eco-design directive Energy-related Products (ErP) Lot 6 Robust output supply protected for output over-current, output short circuit, output over-voltage, and over temperature conditions

Возможности:

Wide Operating Input Range of 85-V to 265-V AC With Full Power Delivery Over Entire Range Designed to Drive Wide Range of Downstream 24-V Industrial Systems and Motor Drives up to 60 W High Efficiency of > 89% at 115-V AC and > 91% at 230-V AC for Wide Load Range From 30% to 100% Load; No External Cooling Needed up to 60°C Ambient Operation Meets Current THD Regulations as per IEC 61000-3-2, Class-A Precision Current Limit Within ±1% Ensures Maximum Power Delivery for Entire AC Voltage Range Very Low Standby Power of < 200 mW Start-up With High Load Capacitance up to 8500 μF Built-in Lossless ORing Feature for Paralleling Multiple Modules Meets the Requirements of Conducted Emissions Standard – EN55011 Class B, EFT Norm IEC6000- 4-4 – Level-3, and Surge Norm IEC61000-4-5 – Level-3 Power Supply With Small PCB Form Factor (96 × 82 mm)

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
The TIDA-00703 is a Digital Feedback controller board to convert analog power supplies into a real-time configurable Constant-Voltage Constant Current (CC-CV) source with dynamically variable output for performing complex battery charging profiles or driving CC/CV loads.This Reference design replaces the traditional analog feedback with a digital feedback. The Presence of an MCU in the feedback loop gives rise to real time monitoring and configuration capability along with an ability to implement non-linear control behavior.

Возможности:

Designed to convert existing analog feedback to digital feedback. Adds real time configurability to the power stage for changing output voltage and current. Can be programmed to control power stages for wide range of output voltage and current Low standby power consumption of less than 2-mA Option for high side and low side current sensing SOC estimation of the Battery when used to control a power supply as Battery charger. Provides redundant protections for Overcurrent, Overvoltage, and Over-temperature. Tested and Validated with a TIDA-00355 Power stage.

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-00704 reference design is a 25W, multiple output, auxiliary power supply designed for use in power converters targeted for Server, Telecom and Industrial system applications. This solution is a multiple output flyback converter implemented using the UCC28700 to provide Constant-Voltage (CV) and Constant-Current (CC) output regulation and uses quasi-resonant valley-switching to achieve higher efficiency. The design is compact and low cost due to minimal component count with all the necessary built-in protections such as output overcurrent and output short circuit. Hardware is designed and tested to pass EFT requirements and meets low power efficiency performance of Department of Energy (DoE) Level VI standards. Additionally, the design has a built-in eFuse for fault isolation on 12V main rail without affecting any other outputs.
Возможности:

Peak overall efficiency of 93% enables energy saving Uses a single UCC29950 combo controller for controlling both PFC and LLC stages for reduced component count True input power limit to provide greater degree of protection under varying input voltage conditions Low stand-by power (<100mW) to help meet no- load condition limits of energy norm (DoE level VI) Wide input voltage range from 85 VAC to 264 VAC helps in meeting global market needs

Возможность заказа
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-00706 reference design is a 25W, multiple output, auxiliary power supply designed for use in power converters targeted for Server, Telecom and Industrial system applications. This solution is a multiple output flyback converter implemented using the UCC28700 to provide Constant-Voltage (CV) and Constant-Current (CC) output regulation and uses quasi-resonant valley-switching to achieve higher efficiency. The design is compact and low cost due to minimal component count with all the necessary built-in protections such as output overcurrent and output short circuit. Hardware is designed and tested to pass EFT requirements and meets low power efficiency performance of Department of Energy (DoE) Level VI standards. Additionally, the design has a built-in eFuse for fault isolation on 12V main rail without affecting any other outputs.
Возможности:

High average efficiency of 83.8% at 400VDC and 87.2% at 165VDC to meet DoE Level VI and EU CoC Tier-2 energy efficiency norms Peak efficiency of ~86% at 400VDC and ~88% at 165VDC at full load Low stand-by power (<100mW) to help meet no- load condition limits of multiple energy norms (DoE level VI and EU CoC Tier-2) Wide input voltage range from 120VDC to 400VDC to power universal input AC-DC converters Multiple outputs: -7.2/5/12V and isolated 6/7.2/11/12V to address all system rails in one unit

Возможность заказа
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
TIDA-00707 is a 1-kW, compact (100mmX80mm) power factor converter (PFC) designed for telecom, server, and industrial power supplies. This reference design is a continuous conduction mode boost converter, implemented using a UCD3138A Digital Power Supply controller with all protections built-in. Hardware is designed and tested to pass conducted emissions, surge, and EFT (as per EN55014) requirements. This reference design provides a ready platform of front-end PFC to address various power supplies up to 1 kW, Improves overall system performance lower bus capacitance, lower RMS currents, and front-end protections. It meets stringent current THD and power factor norms and protects from output overcurrent, overvoltage, and undervoltage conditions.

Возможности:

Wide Operating Input Range: 195-V to 270-VAC Designed to Drive Wide Range of Downstream DC/DC Converters and Inverter-Fed Motors up to 1 kW High Power Factor > 0.99 and < 5% THD From Medium-to-Full Load (50% to 100%); Meets Current THD Regulations as per IEC 61000-3-2 High Efficiency of > 97% at Full Load Over Entire Operating Voltage Range PFC Converter designed with a simple, small PCB form factor (100 x 82mm)

Возможность заказа
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-00708 is a 5-W multiple-output auxiliary power supply designed for use in power converters targeted for applications in industrial, server, telecom, and consumer systems. This reference design is a flyback converter implemented using the device UCC28881 that integrates the controller, 700-V power MOSFET, and internal current sense into one monolithic device. The design is simple, compact, and low cost due to minimal component count with all the necessary protections, such as output overcurrent, output short circuit, and over-temperature conditions, built in. Hardware is designed and tested to pass EFT requirements and meets low-power efficiency performance of Department of Energy (DoE) Level VI.
Возможности:

Designed for wide operating input voltage range from 100 VDC to 450 VDC Very low standby power of <50 mW High efficiency >82% at 165 VDC and >84% at 400 VDC for loads greater than 75% Multiple outputs: 12 V/0.2 A, 3.3 V/0.25 A, 12 V/0.15 A (isolated) Ultra-simple circuit with low-cost off the shelf components with a compact form factor (32 mm x 25 mm)

Возможность заказа
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-00709 is a 36-W, dual output, auxiliary power supply with provision to accept both wide ranges of DC as well as AC input. Based on the input, this TI Design can be used as an adapter or auxiliary power supply designed for use in power converters targeted for server, telecom, and industrial system applications. This reference design is a quasi-resonant (QR) flyback converter implemented using the UCC28740 constant voltage-constant current (CV-CC) flyback controller with optocoupled feedback for voltage and primary-side regulation (PSR) for current. For improved efficiency, the TIDA-00709 uses synchronous rectification with sync controller UCC24636 and low RDS(on) MOSFET for main 12- V_ISO/2.75-A output. Hardware is designed and tested to pass conducted emissions, surge and EFT requirements. Additionally, the design has a built-in eFuse for multiple faults isolation for main output rail without effecting any other output.
Возможности:

High Efficiency of > 90% With AC Input and > 92% With DC Input Minimum Efficiency > 86.5% at 10% Load Aids to Meet 80Plus Titanium Standard of Server PSUs Low Standby Power (≈ 120 mW) Aids to Meet NoLoad Condition Limits of DoE Level VI and EU CoC Tier-I Compact Form-Factor to Achieve High Power Density Solutions: – DC/DC: 40 mm × 45 mm – AC/DC: 70 mm × 45 mm Dual Output: 12 V/0.25 A and 12 V_ISO/2.75 A

Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
The TIDA-00779 is a 3.5-kw, cost competitive power factor regulator converter designed for room air-conditioner and other major appliances. This reference design is a continuous-conduction-mode (CCM) boost converter implemented using TI’s UCC28180 PFC controller provided with all of the necessary built-in protections. The hardware is designed and tested to pass surge, and EFT testing as per the IEC61000 requirements for household appliances.

Возможности:

High efficiency of > 98% over entire operating voltage range and thus get smaller heat sink Wide full load operating input range of 190 VAC to 270 VAC High power factor > 0.99 and less than 5% THD from medium-to-full load (50-100%) Up to 3.5 kw high power output to cover most of single phase input PFC application 8-Pin PFC solution (No AC line sensing Needed) enable a very simply design Reduced current sense threshold minimizes power dissipation High power density for smaller dimension

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01141 TI design provides a reference solution for ±100A shunt-based, high-side continuous bi-directional current measurement addressing applications such as battery current monitoring and current monitoring in UPS, Telecom Rectifiers and Server PSUs. This design achieves high accuracy with low shunt resistance value thus reducing power loss and hence shunt sizing.
Возможности:

Shunt-based ±100A continuous bi-directional current measurement solution for accurate current monitoring applications Tight DC accuracy of <1% across temperatures from 25ЛљC to 85ЛљC Low shunt value offers reduced power loss and enhances the system efficiency High-side current sense solution for batteries ranging from 6V to 60V (12V/24V/36V/48V) and common mode voltage up to 80V Adaptable for current sensing even close to fast switching nodes without any external common-mode filtering Fast (<10us) over-current fault alert in either direction for system safety, with programmable threshold

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01159 design provides a reference solution for half-bridge isolated gated drivers used in driving power stages of UPS, inverters, server and telecom applications. This TI Design is based on the UCC21520 reinforced insulated gate driver from TI, and is capable of driving MOSFETs and SiC-FETs. The reference design contains a built-in isolated push-pull auxiliary power supply for powering the output of the isolated gate driver. By bringing together the isolated gate driver and isolated power supply in a compact board with a form factor (!~30 mm × 35 mm), this reference design provides a fully tested robust half bridge driver solution, capable of withstanding >100 kV/μs common mode transient immunity (CMTI).

Возможности:

Compact gate drive solution for driving power stages used in Mid- and High-Voltage Power Converters, Single-Phase and Three-Phase Inverters High driving current (4-A Source and 6-A Sink) Suits Driving MOSFET/ SiC-FET With Currents upto 100 A and Operating Frequencies up to 2 MHz, reducing switching losses significantly Supports 3250-VPK and 3000-VRMS Basic Isolation Provides very High CMTI of > 100 kV/μs for robust operation in noisy high dv/dt environment Integrated Dead-Time in gate driver improves reliability and avoids accidental shoot through of the power stage. Built-in compact , high efficient isolated supply to power the output side of the gate driver

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01281 reference design is low cost, high efficiency, isolated RS-485, I2C & CAN communication module solution intended for use in industrial systems such as Uninterruptable Power Supplies (UPS) and energy storage banks that require isolated communication and isolated power for RS-485/I2C/CAN transceivers. The design has on-board C2000-Piccolo microcontroller for handling the communications protocol for each of interfaces. The board has in-built, low component count, high efficiency, primary side controlled isolated power supply to generate secondary power for communication transceivers eliminating the need for opto-coupler feedback circuits. The TIDA-01281 design is tested for data transmission under various conditions and under EFT and ESD environment, highlighting the performance of TI devices for robust data transmission in harsh environments.
Возможности:

Simple, efficient, and flexible isolated communication module for RS-485, CAN and I2C interface Robust isolation performance for reliable operation in harsh environments meeting functional Isolation and Immunity of 4000-VPK & 2500-VRMS, 560VPK working voltage Common Mode Transient Immunity (CMTI) of 50 kV/us, for high immunity in noisy environments Meets IEC-61000-4-2: ESD ±8kV contact discharge and indirect discharge by HCP and VCP , and IEC-61000-4-4: EFT ± 2kV for RS485 and ±1kV for CAN A standalone control card with analog and digital interface of C2000 device for test and validation of power stages used in UPS, telecom rectifier, server PSU and battery management system

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01369 reference design is a power supply designed for providing power to lock-step dual-core microcontrollers (MCUs) with functional safety architectures, regulating down from an automotive battery or industrial DC supply in a single stage. MCUs from multiple vendors are supported by the design. The core and I/O rails for the MCU are supervised; if a fault condition occurs, the MCU is disabled by hardware RESET output signals and the latching fault condition is reported to the MCU after normal operation is resumed. The reference design emphasizes the complementary features of three products from TI: the TPS653850-Q1 power management IC (PMIC), the TPS57160-Q1 asynchronous DC-DC buck converter, and the TPS3700-Q1 overvoltage and undervoltage supervisor.
Возможности:

Supports Power and Sequencing Requirements of Various Lock-Step Dual Core MCUs Low-Voltage MCU Core Rail with 3% Voltage Ripple from 5-mA to 1.5-A Load Optimized for Hercules TMS570xxxxx Product Family Supervisor and Reset Signals for MCU with Latching Fault Condition Operates over a Wide VIN from 2.6V to 36V (Ideal for Automotive Battery or Industrial Supplies)

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01494 reference design is a compact, high efficiency, 24-V DC, 480-W nominal, 720-W peak output reference design for industrial AC/DC power supplies. The circuit consists of a front-end continuous conduction mode (CCM) power factor correction (PFC) circuit followed by a robust LLC stage with synchronous rectification. The design enables efficiency greater than 93.5% over a wide load range, allowing the system to work without forced cooling. The LLC stage, based on the UCC256301, takes advantage of the ZCS avoidance feature in the UC256301 to enable peak output power, minimizing the PFC Bulk capacitor for meeting holdup requirements, while making the system robust to short circuit and over current conditions. The UCC24612-2 based synchronous rectifier helps in minimizing the losses in the output rectifier, while its advanced proportional gate drive and dead time optimization features helps to avoid shoot through and minimizes losses.
Возможности:

Peak power conversion efficiency of 94% at 230V AC with average efficiency >93.5% Delivers 20A continuous current and up to 30A peak current for 3 seconds Power factor >0.99 and meets PF and current THD as per IEC 61000-3-2 Class A and EN55022 Class B Conducted Emission standard ZCS avoidance in the LLC stage, enabling wider input voltage range operation and robustness Over current, short circuit, over voltage and over temperature protection Compact form-factor: 155mm x 125mm

Документация:
  • Схемотехника
  • BOM
Описание:
This 20-W multiple output, auxiliary power reference design supports AC/DC industrial power supplies with a wide input voltage range (100-425 VDC). The design achieves a peak efficiency of 85% by using discontinuous conduction mode (DCM) valley-switching of TI’s UCC28704 flyback controller with primary side regulation. The compact design uses a minimum number of components to help protect the system, including output overcurrent and output short circuit. The hardware is tested to meet Conducted Emission norm EN55022 Class A using an external EMI filter.
Возможности:

Peak power conversion efficiency of >85% at 400VDC full load Designed for wide operating input voltage range from 100- to 425-V DC Delivers full power of 20 W over the entire operating voltage range Configurable outputs: 15V (primary referred), 5V & 15V (isolated) Low stand-by power of <100mW Compact form-factor to achieve high power density solutions: 40mm × 40mm

Документация:
  • Схемотехника
  • BOM
Описание:
Vienna rectifier power topology is used in high power three phase power factor (AC-DC) applications such as off-board electric vehicleEV chargers and telecom rectifiers. Control design of the rectifier can be complex. This design illustrates a method to control the power stage using C2000™ microcontrollers. The hardware and software available with this design helps accelerate your time to market. The Vienna rectifier power topology is used in high power three phase power factor correction applications such as off-board electric vehicle charging and telecom rectifiers. This design illustrates how to control a Vienna rectifier using C200-MCU. Learn more about what C2000 MCUs have to offer for electric vehicle applications

Возможности:

Greater than 98% peak efficiency Less than 2% THD at full load and low line powerSUITE software support for easy adaptation of software for a customized power level SFRA enables in circuit verification of control loop designed Up to 2.4KW design with three phase 400Vac VL-L Input

Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
Resonant converters are popular DC-DC converters frequently used in server, telecom, automotive, industrial and other power supply applications. Their high performance (efficiency, power density, etc.), improving requirements of the various industry standards, and the ever increasing power density goals have made these converters a good choice for medium to high power applications. This design implements a digitally controlled 500W two phase interleaved LLC resonant converter. The system is controlled by a single C2000™ microcontroller (MCU), TMS320F28379, which also generates PWM waveforms for all power electronic switching devices under all operating modes. This design implements a novel current sharing technique to accurately achieve current balancing between phases.
Возможности:

Digitally controlled two phase interleaved LLC resonant DC-to-DC converter Excellent current sharing between phases without any additional hardware Peak efficiency: 94.5%. Efficiency > 90% for all loads above 10% of rated load powerSUITE support for easy adaptation of software for a customized power level Fault protection: phase/output over-current, output over-voltage, and input under-voltage and overvoltage Phase shedding with programmable limits

Документация:
  • Схемотехника
  • BOM
Описание:
Interleaved Continuous Conduction Mode (CCM) Totem Pole (TTPL) Bridgeless Power Factor Correction (PFC) is an attractive power topology with use of high band-gap GaN devices, because of high efficiency and reduced size of the power supply. This design illustrates a method to control this power stage using C2000™ MCUs and the LMG3410 GaN FET module. Adaptive dead-time & phase shedding methods are implemented for improved efficiency. The Non- Linear Voltage Compensator is designed to reduce overshoot and undershoot during transients. A software phase locked loop(SPLL) based scheme is chosen to drive the totem pole bridge accurately. The hardware and software available with this design helps accelerate your time to market.
Возможности:

AC Input (90-230Vrms), 50-60Hz and 3.3KW rated power at high line 98.75% peak efficiency and less than 2% Total Harmonic Distortion (THD) powerSUITE support for easy adaptation of the design for user requirement In built frequency response analyzer (SFRA) for verification and design of control loops Low zero crossing distrotion Illustrates Adaptive dead-time, Phase Shedding and Non Linear Voltage Compensator implementation

Документация:
  • Схемотехника
  • BOM
Описание:

TIDM-PSFB-DCDC – референс дизайн полномостового 600 Вт DC-DC преобразователя со сдвигом фаз с цифровым управлением. Сдвигом фаз управляет микроконтроллер Picolo семейства C2000, обеспечивая синхронное выпрямление и управление импульсным током. Микроконтроллер реализует высокопроизводительное управление в режиме импульсного тока без внешних поддерживающих схем, что отличает эту реализацию от остальных микроконтроллерных решений. Этот дизайн способен обеспечить высокую эффективность в широком диапазоне нагрузок с пиковой эффективностью, превышающей 95%, поддерживая при этом  ZVS переключения во всем диапазоне нагрузок. Поддерживается графический интерфейс пользователя для первичной оценки функциональности платы. Дизайн обеспечивает полный комплект необходимой документации.

 

Возможности:

  • Полностью микроконтроллерное управление полномостовым DC-DC преобразователем со сдвигом фаз;
  • Вход 400 В DC, выход 12 В 50 А;
  • Управление в режиме импульсного тока без внешних схем;
  • Синхронное выпрямление для увеличения энергоэффективности;
    Адаптивное отключение при нуле напряжения (ZVS) во всем диапазоне нагрузок;
  • Защита от повреждений, включая низкое и высокое напряжение на входе, перегрузка по току и напряжению на выходе.

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:

TIPD165 – референс-дизайн Ti изолированного решения для измерения тока, выполненный на базе изолированного дельта-сигма модулятора и микроконтроллера TMS320F28377D. Эта схема позволяет измерять ток с помощью шунта в приложениях, требующих превосходную гальваническую изоляцию и точность и может быть использована в промышленных решениях по управлению двигателями, фотогальванических инверторах и счетчиках электроэнергии. Решение позволяет измерять ток нагрузки в пределах -10 А…10 А с точность, превосходящей 0,3% без калибровки, а также обеспечивает двойной функционал канала высокого разрешения и дополнительного канала обнаружения перегрузки и короткого замыкания.

Возможности:

  • Проверенный дизайн, включающий в себя теоретическое описание, выбор компонентов, симуляцию TINA-TI, результаты измерений, PCB дизайн и модификации;
  • Гальванически изолированное решение для измерения тока;
  • 16-битный выход при скорости 78,1 kSPS;
  • ±10А с точностью <0,3% (некалиброванная точность);
  • Отношение сигнал/шум 78 дБ.

Возможность заказа
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:

Это решение замкнутого токового трансдюсера с однополярным питанием разработано для измерения постоянного, переменного и импульсного токов. Решение обеспечивает гальванически изолированное измерение токов до 55 А до достижения насыщения и включает в себя встроенный индукционный датчик.

Возможности:

  • Диапазон измеряемых токов до 55 А;
  • Встроенный индуктивный сенсор;
  • Чувствительность 41,1 мВ/А;
  • Гальванически изолированный токовый трансдюсер.

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM