forward

Источники питания на DIN-рейку для платёжных шлюзов

Описание:
The PMP10100 reference design uses the LM5023 flyback controller for the Quasi-Resonant Flyback Topology. It generates an isolated output (19.5V@3.84A) from an universal input (85VAC - 265VAC).

Возможности:

Quasi-Resonant Flyback Topology Four Point Average Efficiency = 89.3% (Vin=110VAC) Four Point Average Efficiency = 89.4% (Vin=230VAC) 10% Load Efficiency = 89.6% (Vin=110VAC) 10% Load Efficiency = 87.2% (Vin=230VAC)

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
The PMP10283 reference design provides 30V/100W and -30V/100W outputs from AC line voltage to a single LLC resonant converter stage. This design is featured with its low circuit cost and high efficiency (over 90% @ 120VAC full load and ~92% @ 240VAC full load). This design uses the UCC25600 resonant converter controller for LLC resonant converter.

Возможности:

88VAC-132VAC or 176VAC-264VAC Input +/-30V 200W output Up to 92% converter efficiency Single stage AC-DC LLC-SRC Low circuit cost

Возможность заказа
  • Заказать BOM
Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This design uses the PSR controller UCC28630 that is capable of operating in both CCM and DCM. With the help of X-cap discharge function of UCC28630, the safety discharge resistor can be elimiated. Full load efficiency is 83.5% at 120VAC/60Hz input and 86% at 230VAC/50Hz input.

Возможности:

Universal AC input: 85VAC-264VAC CCM/DCM PSR controller UCC28630 12V/75W rated output No need for additional safety discharge circuits Full load efficiency is 83.5% at 120VAC/60Hz input and 86% at 230VAC/50Hz input

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

PSR - Primary-Side Regulation, контроль и  регулировка выходного напряжения осуществляется контроллером в первичной цепи. Такая реализация позволяет сократить BOM изделия за счет отсутствия компонентов обратной связи.

Это решение использует для реализации обратноходового преобразователя 12 В/60 Вт PSR контроллер UCC28710. Использование UCC28710 позволяет удешевить конструкцию и добиться максимальной эффективности 84,3% при входе 120 В/60 Гц и 86% при входе 230 В/ 50 Гц.

Возможности:

  • Универсальный вход: 85-265В;
  • DCM PSR контроллер UCC28710;
  • Номинальный выход 12 В/60 Вт;
  • Эффективность при полной нагрузке 84,3% (120 В/60 Гц) и 86% (230 В/50 Гц).

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10535 reference design is a low profile quad output isolated Fly-Buck power supply for industrial applications. The power supply has a synchronous buck regulator, LM5017, and a low profile (6mm) transformer. It generates four isolated outputs of ±5V, ±12V, 75mA each. The LM5017 is a 100V wide Vin, 600mA synchronous buck regulator. The input voltage range of the design is 20V to 32V, making it suitable for 24V input industrial application. The Fly-Buck can regulate the secondary side outputs without opto-coupler or aux winding and is capable of achieving good cross regulation within ±5%. With LM5017's constan on-time control, no loop compensation is required, which simplifies the design and helps reducing the external part count and BOM cost.

Возможности:

Multiple isolated bias power using Fly-Buck, ideal for PLC and industrial applications 2.5W output power, +/-12V, +/-5V @ 75mA each, with LM5017 capable of 7.5V to 100V input Primary side regulation without opto; good cross regulation (within +/-5%) 6mm low profile transformer Constant on-time control; no loop compensation required and fast transient response Circuit board is tested, and the design files and test report are included.

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP10545 is an Isolated Flyback Converter with the primary configured as a buck-boost inverter, using the LM5160 regulator IC. The design accepts an input voltage of 9Vin to 30Vin and provides four isolated outputs of +5.7Vout, each capable of supplying 350mA. The design uses an easily available off-the-shelf transformer, making it a more cost effective design solution.

Возможности:

Primary side regulation without Opto Good regulation, within ±5% No loop compensation required/fast transient response Low BOM count & cost, compact solution size No RC snubber at primary winding

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP10559 is a non-sync isolated Flybuck-boost converter with a negative primary voltage. The power supply has a synchronous buck regulator, LM5160, and a versa pack transformer. The design accepts an input voltage of 18V to 30V, and outputs 30V, capable of providing 0.67A of current to the load, making it suitable for 24V input industrial application. The Fly-Buck topology can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good regulation within ±5%. With LM5160's Constan On-Time control, no loop compensation is required, which simplifies the design and helps reducing the external part count and BOM cost.

Возможности:

Versa pack transformer increase design versatility +30V/0.67A with LM5160 capable of 4.5V to 65V input Primary Side Regulation without Opto, Good Regulation, within +/-5% Constant On Time Control, No Loop Compensation Required, and Fast Transient Response No primary winding snubber is required

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design implements the UCC28630 PSR controller in a flyback power supply. The UCC28630 is capable of operating in both Continuous and Discontinuous Conduction Modes which enables high efficiency while reducing inductor size and cost. Safety standards such as EN60950 require that any X-capacitors in EMC filters on the AC side of the bridge rectifier quickly discharge to a safe level when AC is disconnected. Typically, this requirement is achieved by including a resistive discharge element in parallel with the X-capacitor. However, this resistance causes a continuous power dissipation that impacts the standby power performance. In order to reduce standby power and eliminate the standing loss associated with the conventional discharge resistors, the UCC28630 device incorporates active X-capacitor discharge circuitry. In this design, less than 100mW no load power comsumption and over 88% converter efficiency is achieved.

Возможности:

Utilize UCC28630 CCM/DCM PSR controller Over 86% average efficiency Optimized US line AC-DC power supply design 24V/4A rated output This circuit is tested and includes a test report

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP10861 uses active clamp forward converter for an isolated 24V to 12V/3.4A conversion. Reverse input connection, output over-current protection, output over-voltage protection, input inrush current limiting circuit are integrated in this board. With wide 9-36V input voltage range, over 89.5% peak efficiency is achieved with 24V input voltage. All the components temperature rise are less than 30oC at full load condition.
Возможности:

24V to 12V/3.4A active clamp forward converter 9V to 36V input voltage range Integrated protections: reverse input connection, output over-current protection, output over-voltage protection Peak 89.5% efficiency with 24V iinput Test report available

Документация:
  • Схемотехника
  • BOM
Описание:
PMP10974 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 89% average efficiency. The design also features UCC2463x synchronous rectification controller.

Возможности:

85VAC to 265VAC, 50/60Hz input 5V/10A/50W output Over 89% average 4-point efficiency Over 85% efficiency at 10% load (5W) Less than 40mW standby power losses Protected against output short-circuits

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
PMP11232 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 89.5% average efficiency. The design also features UCC2463x synchronous rectification controller.
Возможности:

85VAC to 265VAC, 50/60Hz input 5V/6A/30W output Over 90% average 4-point efficiency with 120VAC input Over 89.5% average 4-point efficiency with 230VAC input EMI test data included Less than 40mW standby power losses Protected against output short-circuits

Документация:
  • Схемотехника
  • BOM
Описание:
PMP11236 is a high voltage (105VAC to 440VAC) Buck converter reference design using MOSFET integrated controller UCC28881. 24V/100mA is provided by the UCC28881 Buck converter and followed by a TLV70450 LDO to provide 5V/20mA output. This design is compatible with Class B conduction EMI regulation.

Возможности:

105VAC to 440VAC high voltage input Buck converter with MOSFET integrated controller 24V/100mA and 5V/20mA outputs Conduction EMI verified and test data included Board dimension: W x L = 20mm x 45mm No custom magnetic applied

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
PMP11281 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 88% average efficiency. The design also features UCC2463x synchronous rectification controller.

Возможности:

85VAC to 265VAC, 50/60Hz input, 5V/10A/50W output Over 88% average 4-point efficiency Over 77% efficiency at 10% load (5W) Less than 40mW standby power losses Protected against output short-circuits

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
PMP11282 is ahigh-efficiency AC/DC power supply reference design with universal AC input and 24V/17A output. Interleaved transition mode PFC and LLC series resonant converter is applied for 24V/17A main power. A PSR Flyback with MOSFET integrated controller is applied as the auxiliary supply. 91.98% efficiency is achieved at low line and full load. 94.61% efficiency is achieved at high line and full load.

Возможности:

410W PSU with interleaved transition mode PFC and LLC-SRC 91.98% efficiency at 120VAC/60Hz and full load 94.61% efficiency at 230VAC/50Hz and full load 125mm x 225mm board dimension Test report is available Conduction EMI test results included

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP11303 is high-efficiency AC/DC power supply reference design with universal AC input and 25V/13.5A and 12V/1A outputs. LLC+PFC combo IC UCC29950 is applied for the main power stages with 25V/13.5A output while UCC28730 is applied for the auxiliary power with 12V/1A output. This design has low no load power comsumption (152mW@230VAC) and over 93% peak efficiency. This design also meet 80PLUS Gold requirement for 115VAC Internal power supplies.

Возможности:

Conduction EMI test results included Meet 80PLUS Gold for 115VAC internal power supplies 25V/13.5A and 12V/1A dual outputs 122mm x 200mm board dimension Test report is available Over 98% peak PFC efficiency at high line

Документация:
  • Схемотехника
  • BOM
Описание:
Universal line to 13 volt at 60 watts power supply. This is a synchronous fly back operating in continuous conduction mode using TI's synchronous rectifier controller on the secondary.
Возможности:

Universal line input Synchronous rectification Low cost Low stand-by current

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP11405 reference design uses the UCC28740 constant current (CC), constant voltage (CV) flyback controller for a 5V/1A, 12V/0.9A bias supply with high line AC input (185VAC to 260VAC input). With safety isolated, Over 80% efficiency is achieved at full load and less than 400mW power consumption is observed during no load condition.
Возможности:

High line AC input to 5V/1A and 12V/0.9A dual-output 1.45" x 4.45" board dimension CC & CV is enabled with UCC28740 flyback controller Less than 400mW no load power consumption Cross regulation tested

Документация:
  • Схемотехника
  • BOM
Описание:
PMP20468 is an isolated flyback converter utilizing the LM5022 controller for Power-over-Ethernet applications. This design has a minimum operating input voltage of 36V, a maximum input voltage of 57V, and an output of 12V @ 2A of load current. Switching frequency is set to 420kHz. A custom Wurth transformer is used in this design.
Возможности:

36V to 57V input, 12V @ 2A output LM5022 controller for an isolated flyback topology to achieve over 89% efficiency over all operating conditions Compact size, slim form factor, suitable for power-over-ethernet camera applications Solution size: 81mm x 38mm 91% peak efficiency

Документация:
  • Схемотехника
  • BOM
Описание:
The PMP5315 reference design provides and isolated 14V at 6.5A from a universal AC input. The UCC28600 flyback controller used in this design reduces standby power consumption to less than 250mW by operating in burst mode at light loads, and provides efficiency over 88% at heavier loads by reducing switching losses through quasi-resonant valley switching.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP5322 reference design provides and isolated 14V at 4.7A from a universal AC input. The UCC28600 flyback controller used in this design reduces standby power consumption to less than 200mW by operating in burst mode at light loads, and provides efficiency over 87% at heavier loads by reducing switching losses through quasi-resonant valley switching.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP5761 is designed for hybrid filber/coax system with nominal 40VAC-90VAC input and generate a 24V/3.5A output. A cascade PFC and LLC-SRC two stage system is applied in this design to guarantee high power factor is achieved in nominal input range. Transition mode PFC controller UCC28051 and resonant converter controller UCC25600 are applied to PFC and LLC-SRC, respectively. With PFC output set to 300V, PMP5761 is able to keep out in regulation with input up to 200VAC. 80% converter efficiency is achieved at 40VAC and 87% converter efficiency is achieved at 115VAC.

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP5967 reference design provides a 12V/38A output with over 94% efficiency from a 380VDC input. This design uses the UCC25600 to control the resonant LLC converter. The UCC24610 synchronous rectifier controller is used to control two banks of CSD18501Q5A MOSFETs, eliminating the need for heat sinks on the output rectifiers.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP6570 reference design uses the UCC28050 transition mode PFC controller to generate an isolated 5V/2A output from a universal 90VAC to 300VAC input. This design combines both power factor correction and output regulation in a single stage. In addition, the UCC24610 is used to control a synchronous rectifier on the secondary side of the isolation boundry, improving efficiency.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design provides a compact power solution for 70W (peak) audio systems. This supply accepts a universal AC input, and uses a UCC28610 quasi-resonant flyback controller to generate an isolated 24V. Auxiliary 5V/1.5A and 3.3V/0.1A outputs are also provided. This design is capable of providing power to sustained loads of 30W and peak power loads of 70W with efficiencies up to 85%.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP6740 reference design provides 12V at 18W from a universal AC input of 90VAC-265VAC input. This design uses the TL2844 controller with primary side regulation (no optocoupler) for a low cost power solution.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP6910 reference design delivers an isolated 55V at 2A with PFC from a universal AC input. This design is a modified version of the UCC28600 EVM. The PFC boost portion of the design is unchanged from the original EVM. The UCC28600 quasi-resonant flyback has been modified for the higher output voltage. The flyback portion of the design is over 88% efficient. The total input-to-output effciency of the design is 83% from a 120VAC input and 85% from a 240VAC input. For sustained loads over 1.5A, forced air cooling is recommended.
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design uses the BQ24640 super cap charging controller to charge a large bank of super caps to a voltage below the input bus voltage. During an input bus dropout, the energy from the super caps is used to power a boost converter that can supply 10A of output current at 26.2V. This output can be used to hold up the bus voltage for up to 10 seconds (260W for 10 sec).

Возможности:

Boost Converter efficiency greater than 95% at Vin = 18V and 1A - 10A loads Boost holdup supports 28V bus for longer than 27 seconds using a large 28F super cap bank while delivering 260W Super cap charger provides a constant 3A charge current for a controlled startup time Low cost design requires less than 100mm x 100mm

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7361 is an isolated flyback converter with a 54V/1.1A output. The 18-60VDC input is suitable for 24VDC industrial and 48VDC telecom applications. The 54VDC output can be used to power PoE power sourcing equipment (PSE).

Возможности:

Efficiency of 93% with 48V input and maximum load Good line/load regulation with optocoupler feedback Wide input range 1500Vrms isolation for telecom or PoE Optional capacitors to provide hold up time

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
This reference design uses the UCC2894 to control an active clamp forward converter that generates an isolated 24 V at 7 A from a 380-VDC input. This supply is intended to be used with a PFC boost front end and requires an external 12-V bias voltage for housekeeping on the primary side. This supply is up to 91% efficient at full load.

Возможности:

91% efficiency Clamped drain voltage for reduced emissions Compact form factor 64 mmx 90 mm (2.5 inx 3.5 in)

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design generates an isolated 12V/160W output from a high voltage DC input. This design is intended to operate from the output of PFC front end regulator. The UCC2897A is used to control an active clamp forward converter. Texas Instruments CSD18531Q5A synchronous rectifiers allow this design to achieve over 92% efficiency. An accurate current limit is provided by directly sensing the output current. A clock pulse output is also provided for synchronizing with other converters.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

В данном базовом проекте из высокого постоянного входного напряжения генерируется изолированный выход 5 В (100 Вт). Данный проект разработан для функционирования от выхода аппаратного средства регулятора ККМ. Для управления однотактного прямоходового преобразователя с активным демпфером используется UCC2897A. КПД 91% достигается благодаря использованию самовозбуждающихся синхронных выпрямителей. Точное ограничение тока осуществляется за счёт измерения выходного тока. Также доступен выходной тактовый импульс для синхронизации с другими преобразователями.

 

Возможности:

  • Преобразования из 220-400 В постоянного напряжения в 5 В/ 20 А (100 Вт)
  • КПД 91 %
  • Измерение выходного тока
  • Используется контроллер UCC2897A совместно с синхронными выпрямителями семейства NexFET от TI
  • Топология однотактного прямоходового преобразователя с активным демпфером
  • Уменьшенные потери на проводимость, а также площадь посадочного места синхронных выпрямителей

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7760 is a high voltage flyback DC-DC converter with Q100 and D100 qualification. The design includes an external bias supply to withstand 800V. LM5022 used in the circuit has additional features like an error amplifier, precision reference, line under-voltage lockout, cycle-by-cycle current limit, slope compensation, soft-start, external synchronization capability and thermal shutdown.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Типовое решение PMP7763 – высоковольтный изолированный DC/DC преобразователь. Входное напряжение от 30 до 800 В, выходное – 24 В 250 мА. Во вторичной части схемы не реализована обратная связь по выходному напряжению. Контроль выходного напряжения реализован в первичной части схемы.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7764 is a non-isolated flyback converter. The input voltage ranges from 30 – 800V DC. The output is 20V @ 250mA. It has a high voltage hold off circuit.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
Circuit is a non isolated flyback converter. Vin is 700V to 800V max, converting to 16.5V out at a maximum current of 500mA. The design utilizes an external Error amplifier using an LMC7101 for feedback control. The circuit also uses U102 and Q101(and resistors etc etc…) as an external UVLO circuit. LM5021 features include an ultra-low (25 µA) start-up current, which minimizes power losses in the high voltage start-up network. A skip cycle mode reduces power consumption with light loads for energy conserving applications.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
A 12V nominal OR-ing circuit design, allowing users to select one of the two input supplies to be directed as the power supply to a system.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP7932 is an isolated flyback converter which accepts an input voltage of 12Vin to 24Vin and provides dual polarity ouputs of +12Vout @ 0.25A and -12V @ 0.25A.

Возможности:

Ease of use with off the shelf transformer Internal MOSFET Split rail bias supply Isolated input/output for safety Small solution size 300kHz and 700kHz frequency options Cycle-by-Cycle current limit Small device package size Dmax of 90% Excellent line and load regulation

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Изолированный обратноходовой преобразователь с постоянным высоким входным напряжением (диапазон от 300 В до 600 В) и изолированным выходом 20 В при токе 1,5 А.

Данный базовый проект имеет характер аппаратного решения.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
Low EMI, high efficiency, high power factor and reliable power supply are main focus of the PMP8911 design for telecom applications. Transient mode (TM) power factor correction (PFC) with UCC28051 and LLC series resonant converter (SRC) with UCC25600 are applied in PMP8911. Low EMI is expected with zero voltage switching on TM-PFC and LLC-SRC switches. An overall 92% efficiency is achieved at 100W full load. In addition, several protections are embedded into this design which includes input under-voltage protection, input over-voltage protection, output over-voltage protection, and output hic-cup over-power protection.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Типовое решение PMP8920 – надежный и эффективный источник питания с низким EMI и высоким коэффициентом мощности, предназначенный для применения в сфере телекоммуникаций. Переходной режим (TM) коррекции коэффициента мощности (PFC) на базе UCC28051 и LLC резонансный преобразователь (SRC) на базе UCC25600 применялись ранее в решении PMP8911. В данном решении дополнительно после LLC используется синхронный выпрямитель UCC24610. Низкий уровень EMI достигается за счет переключения TM-PFC и LLC-SRC при переходе напряжения через 0. Общий КПД достигает 91% при полной нагрузке 100 Вт. Дополнительно в данное решение встроена защита от повышенного и пониженного напряжения на входе, повышенного напряжения на выходе и защита от перегрузки выхода.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP8930 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 20V output from a univeral AC input. a bulk capacitor with slow-charge-fast-discharge circuit is placed at flyback output to provide long hold up time for the following step-down DC-DC stages. TPS54335 is used as the controller and power stage for the main 4V or 12V output. The valley switching of the UCC28710 allows this low-cost design to achieve a maximum load efficiency of 83%; no load losses are less than 70mW.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP9041 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 24V/40W output from a univeral AC input. The valley switching of the UCC28710 allows this low-cost design to achieve a maximum load efficiency of 90%; no load losses are less than 50mW.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP9409 reference design is an 4-output isolated Fly-Buck power supply for PLC applications. It takes 24V nominal input and provides 4 isolated sets of (+15V) bias voltage, Each rail has a load of 30mA. Each set of rails is generated from one single transformer windings on the secondary side. A compact solution size is achieved (56x43mm). The design features the LM5017 synchronous buck converter configured as a Fly-Buck regulator. With the benefit of primary side regulation, the supply has the outputs regulated without the opto-coupler or additional transformer winding. The LM5017 has a wide Vin range which is up to 100V and 600mA output current capability with integrated switch FETs. The input voltage to the reference board can be loosely regulated with a range of 17V to 36V.

Возможности:

Four isolated outputs, 4x(+15V@30mA) Fly-Buck converter design, primary side regulation, compact solution for multiple isolated output supply Wide input voltage range of 17V to 36V 85% peak efficiency. LM5017 sync buck regulator, up to 100V wide Vin range, 600mA capability This circuit board is tested, and the design files and test report are included.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Высокие КПД и коэффициент мощности, а также надёжность источника питания – вот главные акценты проекта PMP9531 для применения в драйверах двигателей. В проекте PMP9531 применены корректор коэффициента мощности (PFC) UCC28051, работающий в переходном режиме (TM), и последовательный резонансный преобразователь подуровня логической связи UCC25600. Кроме того, в качестве источника смещённого напряжения использован понижающий преобразователь с включением на верхней стороне UCC28710. На высоком уровне сигнала достигается КПД преобразования 93 %, в то время как на низком уровне сигнала сохраняется КПД преобразования 90 %.

Возможности:

  • Универсальный вход (85-264 В переменного напряжения);
  • Выход 28 В / 350 Вт;
  • КПД преобразования до 93 %;
  • Выходная мощность PFC в режиме TM доходит до 385 Вт;
  • Понижающий AC/DC-преобразователь с включением на высокой стороне в качестве источника смещённого напряжения.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Высокие КПД и коэффициент мощности, а также надёжность источника питания – вот главные акценты проекта PMP9640 для применения в драйверах двигателей. Для безмостового ККМ в первом каскаде преобразования PMP9640 применён недорогой аналоговый контроллер ККМ в переходном режиме (TM) UCC28051. Во втором каскаде преобразования PMP9640 применён последовательный резонансный преобразователь (SRC) подуровня логической связи UCC25600. Кроме того, в качестве источника смещённого напряжения использован понижающий преобразователь с включением на верхней стороне UCC28710. В данном проекте КПД безмостового ККМ может достигать 98,5 %.

 

Возможности:

  • Универсальный вход (85 - 264 В переменного напряжения)
  • Выход 28 В/ 310 Вт
  • КПД ККМ до 98,5 %
  • Выходная мощность ККМ в режиме TM доходит до 365 Вт
  • Понижающий AC/DC-преобразователь с включением на высокой стороне в качестве источника смещённого напряжения

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
24V Output, Constant Voltage / Constant Current, 65W Flyback power supply with 130W surge capability. Primary side regulation eliminates feedback opto-coupler and provides 1% regulation down to no-load. Average efficiency of > 89% and no load power of < 70mW are achieved. Voltage input range is 85VAC-265VAC Input.

Возможности:

Primary Side Regulation (PSR) +/- 1% Voltage Regulation +/- 7.5% Current Regulation <70mW Stand-by Power Short Circuit Protection High Voltage Startup > 85% Efficiency at 10% load

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP9730 reference designemploys the UCC28051 power factor correction controller to implement a single stage PFC-Flyback AC/DC converter that generates an isolated 12V output at 3A from a universal AC input. The design features UCC28910 primary side regulation Flyback switcher for generating the VDD bias rails and the UCC24610 for 2ndary side synchronous rectification. This provides an excellent solution for systems such as motor drives requiring an isolated bus voltage, good power factor and high efficiency.

Возможности:

89% 4-pt average efficiency 90% peak efficiency >0.85 Power factor at 100% load No aluminum capacitors for small size and high reliability Small form factor 50mm X 50mm x 18mm (2" X 2" X 0.7")

Документация:
  • Схемотехника
  • BOM
Описание:
PMP9750 is a CLL resonant converter reference design with 400VDC input and 28V/9A ouput. Unlike LLC series resonant converter, CLL resonant converter used in PMP9750 utilizes its output inductor to minimize the size of the resonant tank. With resonant controller UCC25600 and bridge driver UCC27714, PMP9750 is able to achieve 95.7% peak efficiency.

Возможности:

400VDC input to 28V/9A output Utilize compact, high efficieny CLL resonant converter Test data included Board dimension: W x L x H = 2.05" x 3.8" x 1.21" Achieve 95.7% peak efficiency

Документация:
  • Схемотехника
  • BOM
Описание:

Высокопроизводительный индикатор тока на основе шунта используется для измерения напряжения протекающего через измерительный резистор, когда через него проходит ток. Дополнительно реализуется внешняя схема защиты от пульсаций и быстрых переходных процессов, демонстрируют различные уровни противодействия в соответствии EC61000-4-4 и IEC61000-4-5.

Возможности:

  • Способность поглощать пульсации в соответствии с требованиями IEC-61000-4;
  • Способность поглощать пульсации в соответствии с требованиями IEC-61000-5;
  • Выбор коэффициента усиления:
    • INA210: 200 V/V
    • INA211: 500 V/V
    • INA212: 1000 V/V
    • INA213: 50 V/V
    • INA214: 100 V/V
    • INA215: 75 V/V

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-00477 reference design is a continuous conduction mode boost converter implemented using TI digital power supply controller UCD3138A and with all the necessary protections built-in. TIDA-00477 PFC is designed to improve overall system performance with lower bus ripple, lower bus capacitance, and lower RMS currents than traditional PFC power supplies. In addition, the design provides precise information of the input energy consumption of the unit. Hardware is designed and tested to pass conducted emissions, surge, and EFT as per EN55014 – requirements.

Возможности:

Wide operating input range 195-VAC to 270-VAC Designed to drive wide range of downstream DC/DC converters and inverter fed motors up to 1kW High power factor > 0.99 and less than 5% THD from medium-to-full load (50-100%). Meets Current THD regulations as per IEC 61000-3-2 High efficiency of > 97% at full load over entire operating voltage range. It eliminates need for external cooling up to 55oC ambient operation for loads ≤ 850W Communicates the input power consumption information of the unit precisely for all load conditions. Built-in 12V/3W supply for house-keeping power needs PMBUS & Isolated UART for communication Meets the requirements of Conducted Emissions standard – EN55011 class A, EFT norm IEC6000-4-4, and Surge norm IEC61000-4-5 Power supply designed with a simple, small PCB form factor (165 x 95mm)

Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:

Данное типовое решение – LLC резонансный полумостовой DC/DC преобразователь с цифровым управлением через дочернюю плату 3138ACC32EVM-149. Дочерняя плата с предустановленным встроенным программным обеспечением реализует функции управления, требуемые для LLC резонансного полумостового преобразователя. Постоянное напряжение на входе TIDA-00512 (3138ALLCEVM-150) от 350 В до 450 В, номинальное напряжение на выходе 12 В при максимальном токе 29 А, выходная мощность при полной нагрузке 340 Вт.

 

Возможности:

  • Синхронный выпрямитель
  • Оптимальная эмуляция диодов и Dead-Time в синхронном выпрямителе
  • Ограничение тока в соответствии с рабочим циклом
  • Автоматическое переключение между режимами LLC и PWM
  • Контрольные точки для облегчения процесса тестирования топологии

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
TIDA-00701 is a 100W, 24V, Industrial AC-DC power supply designed for use in Industrial & Instrumentation systems such as process controls, factory automation and machinery control. This reference design has front end Power Factor Correction (PFC) circuit designed using UCC28051 PFC controller, followed by Quasi-Resonant flyback converter implemented using UCC28740 Primary Side regulated (PSR) CC-CV flyback controller, with all the necessary protections built-in. Hardware is designed and tested to pass conducted emissions, surge, and EFT requirements. The key highlights of this reference design are: Reduced component count design to achieve NEC Class-2 and Limited Power Source (LPS) norms Meets Energy Star Rating and 2013 EU eco-design directive Energy-related Products (ErP) Lot 6 Meets stringent current THD norms Robust output supply protected for output over-current, output short circuit, output over-voltage, and over temperature conditions

Возможности:

Wide operating input range 85-VAC to 265-VAC, with full power delivery over entire range. Designed to drive wide range of downstream 24V Industrial systems and motor drives up to 100W. High efficiency of 88% at 115VAC and >89% at 230VAC for wide load range from 40% to 100% load. No external cooling needed up to 60oC ambient operation High power factor >0.97 at both 115VAC and 230VAC for 100% load. Meets Current THD regulations as per IEC 61000-3-2, Class-A. Precision current limit within ±1% ensures maximum power delivery for entire AC input voltage range. Very low standby power of < 200mW. Start-up with high load capacitance up to 8500uF Built-in loss-less ORing feature for paralleling multiple modules Meets the requirements of Conducted Emissions Standard – EN55011 class B, EFT norm IEC6000-4-4 –Level-3, and Surge norm IEC61000-4-5 –Level-3.

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-00702 is a 60-W, industrial AC-DC power supply designed for use in industrial and instrumentation systems such as process controls, factory automation, and machinery control. This reference design is a Quasi-resonant (QR) flyback converter implemented using the UCC28740 CC-CV flyback controller with optocoupled feedback for voltage and primary-side regulation (PSR) for constant current regulation, with all the necessary protections built-in. Hardware is designed and tested to pass conducted emissions, surge, and EFT requirements. The key highlights of reference design: Reduced component count design to achieve NEC Class-2 and Limited Power Source (LPS) norms Meets Energy Star Rating and 2013 EU eco-design directive Energy-related Products (ErP) Lot 6 Robust output supply protected for output over-current, output short circuit, output over-voltage, and over temperature conditions

Возможности:

Wide Operating Input Range of 85-V to 265-V AC With Full Power Delivery Over Entire Range Designed to Drive Wide Range of Downstream 24-V Industrial Systems and Motor Drives up to 60 W High Efficiency of > 89% at 115-V AC and > 91% at 230-V AC for Wide Load Range From 30% to 100% Load; No External Cooling Needed up to 60°C Ambient Operation Meets Current THD Regulations as per IEC 61000-3-2, Class-A Precision Current Limit Within ±1% Ensures Maximum Power Delivery for Entire AC Voltage Range Very Low Standby Power of < 200 mW Start-up With High Load Capacitance up to 8500 μF Built-in Lossless ORing Feature for Paralleling Multiple Modules Meets the Requirements of Conducted Emissions Standard – EN55011 Class B, EFT Norm IEC6000- 4-4 – Level-3, and Surge Norm IEC61000-4-5 – Level-3 Power Supply With Small PCB Form Factor (96 × 82 mm)

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
The TIDA-00704 reference design is a 25W, multiple output, auxiliary power supply designed for use in power converters targeted for Server, Telecom and Industrial system applications. This solution is a multiple output flyback converter implemented using the UCC28700 to provide Constant-Voltage (CV) and Constant-Current (CC) output regulation and uses quasi-resonant valley-switching to achieve higher efficiency. The design is compact and low cost due to minimal component count with all the necessary built-in protections such as output overcurrent and output short circuit. Hardware is designed and tested to pass EFT requirements and meets low power efficiency performance of Department of Energy (DoE) Level VI standards. Additionally, the design has a built-in eFuse for fault isolation on 12V main rail without affecting any other outputs.
Возможности:

Peak overall efficiency of 93% enables energy saving Uses a single UCC29950 combo controller for controlling both PFC and LLC stages for reduced component count True input power limit to provide greater degree of protection under varying input voltage conditions Low stand-by power (<100mW) to help meet no- load condition limits of energy norm (DoE level VI) Wide input voltage range from 85 VAC to 264 VAC helps in meeting global market needs

Возможность заказа
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
Описание:
TIDA-00707 is a 1-kW, compact (100mmX80mm) power factor converter (PFC) designed for telecom, server, and industrial power supplies. This reference design is a continuous conduction mode boost converter, implemented using a UCD3138A Digital Power Supply controller with all protections built-in. Hardware is designed and tested to pass conducted emissions, surge, and EFT (as per EN55014) requirements. This reference design provides a ready platform of front-end PFC to address various power supplies up to 1 kW, Improves overall system performance lower bus capacitance, lower RMS currents, and front-end protections. It meets stringent current THD and power factor norms and protects from output overcurrent, overvoltage, and undervoltage conditions.

Возможности:

Wide Operating Input Range: 195-V to 270-VAC Designed to Drive Wide Range of Downstream DC/DC Converters and Inverter-Fed Motors up to 1 kW High Power Factor > 0.99 and < 5% THD From Medium-to-Full Load (50% to 100%); Meets Current THD Regulations as per IEC 61000-3-2 High Efficiency of > 97% at Full Load Over Entire Operating Voltage Range PFC Converter designed with a simple, small PCB form factor (100 x 82mm)

Возможность заказа
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-00708 is a 5-W multiple-output auxiliary power supply designed for use in power converters targeted for applications in industrial, server, telecom, and consumer systems. This reference design is a flyback converter implemented using the device UCC28881 that integrates the controller, 700-V power MOSFET, and internal current sense into one monolithic device. The design is simple, compact, and low cost due to minimal component count with all the necessary protections, such as output overcurrent, output short circuit, and over-temperature conditions, built in. Hardware is designed and tested to pass EFT requirements and meets low-power efficiency performance of Department of Energy (DoE) Level VI.
Возможности:

Designed for wide operating input voltage range from 100 VDC to 450 VDC Very low standby power of <50 mW High efficiency >82% at 165 VDC and >84% at 400 VDC for loads greater than 75% Multiple outputs: 12 V/0.2 A, 3.3 V/0.25 A, 12 V/0.15 A (isolated) Ultra-simple circuit with low-cost off the shelf components with a compact form factor (32 mm x 25 mm)

Возможность заказа
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-00709 is a 36-W, dual output, auxiliary power supply with provision to accept both wide ranges of DC as well as AC input. Based on the input, this TI Design can be used as an adapter or auxiliary power supply designed for use in power converters targeted for server, telecom, and industrial system applications. This reference design is a quasi-resonant (QR) flyback converter implemented using the UCC28740 constant voltage-constant current (CV-CC) flyback controller with optocoupled feedback for voltage and primary-side regulation (PSR) for current. For improved efficiency, the TIDA-00709 uses synchronous rectification with sync controller UCC24636 and low RDS(on) MOSFET for main 12- V_ISO/2.75-A output. Hardware is designed and tested to pass conducted emissions, surge and EFT requirements. Additionally, the design has a built-in eFuse for multiple faults isolation for main output rail without effecting any other output.
Возможности:

High Efficiency of > 90% With AC Input and > 92% With DC Input Minimum Efficiency > 86.5% at 10% Load Aids to Meet 80Plus Titanium Standard of Server PSUs Low Standby Power (≈ 120 mW) Aids to Meet NoLoad Condition Limits of DoE Level VI and EU CoC Tier-I Compact Form-Factor to Achieve High Power Density Solutions: – DC/DC: 40 mm × 45 mm – AC/DC: 70 mm × 45 mm Dual Output: 12 V/0.25 A and 12 V_ISO/2.75 A

Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
The TIDA-01141 TI design provides a reference solution for ±100A shunt-based, high-side continuous bi-directional current measurement addressing applications such as battery current monitoring and current monitoring in UPS, Telecom Rectifiers and Server PSUs. This design achieves high accuracy with low shunt resistance value thus reducing power loss and hence shunt sizing.
Возможности:

Shunt-based ±100A continuous bi-directional current measurement solution for accurate current monitoring applications Tight DC accuracy of <1% across temperatures from 25ЛљC to 85ЛљC Low shunt value offers reduced power loss and enhances the system efficiency High-side current sense solution for batteries ranging from 6V to 60V (12V/24V/36V/48V) and common mode voltage up to 80V Adaptable for current sensing even close to fast switching nodes without any external common-mode filtering Fast (<10us) over-current fault alert in either direction for system safety, with programmable threshold

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01159 design provides a reference solution for half-bridge isolated gated drivers used in driving power stages of UPS, inverters, server and telecom applications. This TI Design is based on the UCC21520 reinforced insulated gate driver from TI, and is capable of driving MOSFETs and SiC-FETs. The reference design contains a built-in isolated push-pull auxiliary power supply for powering the output of the isolated gate driver. By bringing together the isolated gate driver and isolated power supply in a compact board with a form factor (!~30 mm × 35 mm), this reference design provides a fully tested robust half bridge driver solution, capable of withstanding >100 kV/μs common mode transient immunity (CMTI).

Возможности:

Compact gate drive solution for driving power stages used in Mid- and High-Voltage Power Converters, Single-Phase and Three-Phase Inverters High driving current (4-A Source and 6-A Sink) Suits Driving MOSFET/ SiC-FET With Currents upto 100 A and Operating Frequencies up to 2 MHz, reducing switching losses significantly Supports 3250-VPK and 3000-VRMS Basic Isolation Provides very High CMTI of > 100 kV/μs for robust operation in noisy high dv/dt environment Integrated Dead-Time in gate driver improves reliability and avoids accidental shoot through of the power stage. Built-in compact , high efficient isolated supply to power the output side of the gate driver

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01281 reference design is low cost, high efficiency, isolated RS-485, I2C & CAN communication module solution intended for use in industrial systems such as Uninterruptable Power Supplies (UPS) and energy storage banks that require isolated communication and isolated power for RS-485/I2C/CAN transceivers. The design has on-board C2000-Piccolo microcontroller for handling the communications protocol for each of interfaces. The board has in-built, low component count, high efficiency, primary side controlled isolated power supply to generate secondary power for communication transceivers eliminating the need for opto-coupler feedback circuits. The TIDA-01281 design is tested for data transmission under various conditions and under EFT and ESD environment, highlighting the performance of TI devices for robust data transmission in harsh environments.
Возможности:

Simple, efficient, and flexible isolated communication module for RS-485, CAN and I2C interface Robust isolation performance for reliable operation in harsh environments meeting functional Isolation and Immunity of 4000-VPK & 2500-VRMS, 560VPK working voltage Common Mode Transient Immunity (CMTI) of 50 kV/us, for high immunity in noisy environments Meets IEC-61000-4-2: ESD ±8kV contact discharge and indirect discharge by HCP and VCP , and IEC-61000-4-4: EFT ± 2kV for RS485 and ±1kV for CAN A standalone control card with analog and digital interface of C2000 device for test and validation of power stages used in UPS, telecom rectifier, server PSU and battery management system

Документация:
  • Схемотехника
  • BOM
Описание:

TIPD165 – референс-дизайн Ti изолированного решения для измерения тока, выполненный на базе изолированного дельта-сигма модулятора и микроконтроллера TMS320F28377D. Эта схема позволяет измерять ток с помощью шунта в приложениях, требующих превосходную гальваническую изоляцию и точность и может быть использована в промышленных решениях по управлению двигателями, фотогальванических инверторах и счетчиках электроэнергии. Решение позволяет измерять ток нагрузки в пределах -10 А…10 А с точность, превосходящей 0,3% без калибровки, а также обеспечивает двойной функционал канала высокого разрешения и дополнительного канала обнаружения перегрузки и короткого замыкания.

Возможности:

  • Проверенный дизайн, включающий в себя теоретическое описание, выбор компонентов, симуляцию TINA-TI, результаты измерений, PCB дизайн и модификации;
  • Гальванически изолированное решение для измерения тока;
  • 16-битный выход при скорости 78,1 kSPS;
  • ±10А с точностью <0,3% (некалиброванная точность);
  • Отношение сигнал/шум 78 дБ.

Возможность заказа
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы